Jump to content

RadarRacing

Members
  • Posts

    1,973
  • Joined

  • Last visited

  • Days Won

    2

Everything posted by RadarRacing

  1. ttt anything to trade?
  2. I have a set of intakes for 33-35mm carbs will fit keihins or mikunis. They are the non crossover, non boost bottle intakes. They are the upp black rubber ones. No cracks or anything they work fine. They come with clamps. Do not come with bolts, use your factory or aftermarket ones. No pics you know what the cheap black rubber intakes look like. $50 shipped obo. Might trade for billett stuff or?
  3. PRICES please on yer stuff. Do you have an aluminum drag axle?
  4. If you dont want to buy a cover and everything you can get a gigot undercover lockup. That's what I use it's a slick setup and it holds.
  5. OMG how long will this freakin go on before we can get a price on the stinkin pipes! I also need an alum axle. Dont PM me a price just post it.
  6. Listen to your builder once again is my vote. My 421 CUB runs better with BB shearers, had more torque and I was told it might not rev quite as far but it's peak hp and torque was at 10K ,it had 90% of that in the 8K to 9K range as well. I'm running inframes too. A good builder that's tested pipes on the dyno will know just listen to him. Radar
  7. I've got a parts bike if you need anything.
  8. They kick butt but they arent cheap. Theres about 3 diff types for quads they are all pricey but nice.
  9. I'd go + 6 austin on your setup unless you are really light bike or rider.
  10. He got a pretty nice set for cheap on another site.
  11. Anyone looking to go from a drag setup to a good duner susp. I'm lookin for hillshooter marvins, aluminum axle, drag arms, +8 or 10" swinger etc. I'd kinda like to work some type of trade one way or the other. I have Elka resi rear, +6 stock carrier, axle, elka dune editions on front. My axle,arms etc are stock. Radar
  12. I'd be interested in a trade for swingarm and maybe the marvin. I have a +6 CFM style grey hammer finish swinger. Kinda thinkin of goin to a +10. You can pm back if interested.
  13. Plug fouling is jetting. I'd run a mix as well. +4 timing, 19cc domes wont make it foul plugs but being really rich would. Hope this helps.
  14. T3s have always been good pipes.
  15. I got a set of front stockers with sand tires I'd sell cheap.
  16. Anybody that sells a lot of pipes has them more than likely. Shearers take 2 of the longer springs as well. I'd call Jeff at Fast he has about everything and is very good to deal with.
  17. 4 mil cub cyls are all the same they use a 115 (long) rod which is what your 4 mil cranks mostly come with.
  18. 35.5mm PWK airykers $250
  19. They kick ass. I got the light one to fit under my stock cover with an insert for an 8 plate clutch. It's easy to install and works great. It's called a "Undercover" slingshot lockup. Nate Mccoy at Mccoy's Perf. is where I got mine. I think they are just over $200 or maybe $230 I dont remember. My light model cost a little less.
  20. Check plugs sounds like jetting/electrical issue or something else not clutch. Plugs fouled?
  21. What Pa said is exactly right. They are usaually in the 148-158 range, 48 pilot. I'll bet your bike wont rev out till it's really revving and not under a big load. I had a 400 cub and ran 155s, my 421 cub now has 148s in the same carbs. Many are 155s with pods and pipes. you need to check your needles many of them come with needles that dont work well with banshee motors. CEL nedles arent too much $ if you dont have them.
  22. RadarRacing

    CARB

    They usually use a 35mm or 39mm keihin PWK. I have a set of carbs 35.5 keihins i'd separate if you had another buyer for the other one or buy both for $250 and you could sell the other or convert it to alcohol and keep it. Then you'd get the carb you need plus the richer cel needle and jets.
  23. There gone now. Sold... I thought i had em priced fair.
  24. Thanks jared I have a set of carbs comin traded for pipes. I'll be selling the gas 35s soon.
  25. RadarRacing

    PWK's

    I have some 35.5s Keihin PWK airstrykers I'm pullin off my 4mil cub. I'm just goin a little bigger and alky. I have $30 in needles and mainjets to go with it. I'll take $250 or i'll prolly put em ebay in a week or so. I dont have pics they are on the bike in the toyhauler. If you you want the carbs i'll take pics for ya before any sale. They look and run new. Radar
×
×
  • Create New...