ClaudeMachining Posted May 8, 2018 Author Report Posted May 8, 2018 Leave it &Just Stitch make america great again across the back in yellow Sent from my XT1080 using Tapatalk TRUMP 2020 on the back would be better.Or both ;-)Envoyé de mon SM-G935W8 en utilisant Tapatalk Quote
ClaudeMachining Posted May 8, 2018 Author Report Posted May 8, 2018 i bet you do sit on IT once in a while EL OH EL !!!!!You wish.Envoyé de mon SM-G935W8 en utilisant Tapatalk Quote
BlackandYellowBanshee Posted May 8, 2018 Report Posted May 8, 2018 Did you have to modify the frame to get the shop stool to fit? I definitely like the color combo. It’ll look great when finished. Quote
ClaudeMachining Posted May 8, 2018 Author Report Posted May 8, 2018 Cases trenched and bored.Envoyé de mon SM-G935W8 en utilisant Tapatalk Quote
375hp banshees Posted May 9, 2018 Report Posted May 9, 2018 U tackle it, or send out?Sent from my XT1080 using Tapatalk Quote
ClaudeMachining Posted May 9, 2018 Author Report Posted May 9, 2018 U tackle it, or send out?Sent from my XT1080 using TapatalkI taught about doing it, but since I never did it, I choose to buy new cases and Redline did the job.I still have to sets of cases to play with ;-)Envoyé de mon SM-G935W8 en utilisant Tapatalk Quote
trickedcarbine Posted May 11, 2018 Report Posted May 11, 2018 On May 9, 2018 at 9:07 AM, ClaudeMachining said: I taught about doing it, but since I never did it, I choose to buy new cases and Redline did the job. I still have to sets of cases to play with ;-) Envoyé de mon SM-G935W8 en utilisant Tapatalk No shame in that. That's thinking like a pro when you send it out to be done by the experienced pro. Quote
ClaudeMachining Posted May 11, 2018 Author Report Posted May 11, 2018 No shame in that. That's thinking like a pro when you send it out to be done by the experienced pro. Yeah, not much material left after he bored the cases lol.Envoyé de mon SM-G935W8 en utilisant Tapatalk Quote
ClaudeMachining Posted June 2, 2018 Author Report Posted June 2, 2018 That doesn't fit. I can't put back the pin and the impeller is rubbing on the case...Somebody had similar issue with Mull impeller???Envoyé de mon SM-G935W8 en utilisant Tapatalk Quote
ClaudeMachining Posted June 2, 2018 Author Report Posted June 2, 2018 Get chariotThis one should work, I'll double check.Envoyé de mon SM-G935W8 en utilisant Tapatalk Quote
kawa110 Posted June 2, 2018 Report Posted June 2, 2018 I remember reading ther was a aftermarket impeller that would get “grooved” easily and cause a problem. I don’t remember if it was mull, could have been modquad.That’s why I went chariot Quote
broke350 Posted June 4, 2018 Report Posted June 4, 2018 I didn't have any problems with my Mull impeller, but my buddy did. Turned out the bearing wasn't all the way seated. Just had to tap it in a little further and it spun freely. Quote
RagunCajun Posted June 4, 2018 Report Posted June 4, 2018 On 5/7/2018 at 2:37 PM, Buckeye513 said: Black gripper This. I have very little gripper material on my seat and my body slides back VERY easily with the power i make. I recommend the whole seat in gripper material. It will be ugly but it's much easier and safer to ride. Quote
sleeper06 Posted June 5, 2018 Report Posted June 5, 2018 Are you using a direct drive cover? If so use the stock pump. There are a few reasons to do so. If I’m not mistaken the shaft and impeller can separate. You might be able to space the two apart. Before anything is done make sure the seal n bearing are pressed in 100% or it will cause issue your having Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.