Bansh-eman
-
Posts
8,477 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Store
Everything posted by Bansh-eman
-
it wont hurt anything to go a little over, torque specs are to make sure you get the bolts tight enough that they wont fall out without over doing it and ripping out the threads
-
i mean there isnt dick behind you in that pict, your in the middle of nothing it looks like.
-
yup its just some odd parts that not many ppl need, so i keep posting.
-
talk about the middle of fuking no where!
-
jus hit 1 star now...
-
looking for oen of those flag holder thinga majigs. needs to be blue or plain billet.
-
i hit 41 tonight, that p90 is fuking awsome! i carry the p90 with reddot, then 3 frags, overkill with mp5, and steady aim. some of these guys are rediculose. this guy had tripple the kills as me using nothing but a knife. i was 2nd place with like 30 kills too
-
you might look into wicked a arms off ebay, they are pretty nice , they are cheaper then that and come with everything you need. thats the set i just got for this build only thing that sucks is if u want them chromed u have to send them some where casue they dont chrome
-
bump skiddy bump
-
found it, its 7.4 ft lbs
-
im pretty sure its 7.7 lbs but i dont have time to check right now i got to get going. sry
-
yea im taking off on friday, and ill be gone 30 days. Those Arms are Wicked Arms off Ebay
-
belt fed gatlen shotguns would probly do the trick
-
two of those picts look like some shit out of a mag or a tv commercial
-
fitz just to be clear, what i had said before is NOT a leak down test.... you need to make a leak down tester that builds pressure in your motor that should hold for a certain amount of time. click the link in my sig to see what is needed to make one.
-
im sure ebay....
-
oh yea i guess i should have stated, you want to turn each bolt a little at a time and not put one all the way in then the next and the next and so on... you want to try and keep them nice and even so you dont eat the thread up, its ez u will see
-
yup u need to drain your fluid and oil. remove your clutch cover and pull the 6 screws that hold the old springs on. pop the new ones on there and re tighten. i think they torque is like 7.7 lbs.
-
IMS Tank ( NO cap or petcock ) $175 Aluminum Bumper $50 Stock Coil $50 Lower Motor Mounts $15 Eibach 8 Inch Coil over Rear Spring 0800-225-0375, Used but good condition. $30 If you wish to use Paypal You add 3% for fees. If not I will take money orders. All parts plus shipping.
-
Need help with clutch basket o-ring asap.
Bansh-eman replied to RUDEDAWG's topic in Banshee Repairs and Mods
rudedawg, i have seen problems not using the oring if your running a bone stock clutch and oem plates. i have also seen guys not have a single problem. so its kind of hit or miss. also if you have aftermarket plaes you dont run the oring. -
i did the exchange rate and the site said 8049 canadian dollars conversion said 8006.56
-
i had to try and update my punkbuster casue i was getting some crazy error and it would kick me out of the server
-
8 grand is fuking retarded! im not sure if you would be able to bring it from canada to the states and register it. Either way wouldnt make much sense. they are the same bike as any other 97 to present banshee with differant plastics, just buy those
-
well that sux that its gone to the powder coater and you lost interest good luck though
-
finally sent mt motor out 2 day
Bansh-eman replied to HardIzZlE's topic in General Banshee Discussion
you mean might as well?