Oilsmoke

Well like i said Proflow sells a left & right set of Vm.s 34mm bored to 35.2 for 259.98 Which matches up good with my 35mm intakes. I like the left & right idea. they are shorter carb too. If i was to add UFO's they claim better flow that a Tm series too. This setup would cost little more than the TMX but would look more sleeper too. On The other hand TMX is a Smooth bore in desgin and would flow better in the Hi rpm range and the are better siuted for big hard whoops which my shee see alot of at the bottom of Thunder. Choices :)That was why i am looking for some input.

Looks like I have to be a Pioneer agian.

Asset. Personally I would Not run a 2,000.00+ engine with a nonwelded crank. If you are only ported & piped and don't thrash your Shee like a hill shootin drag racing craised speed demon than you could go for a few years on a new crank. But who ride the shee like that? Welded & trueing are Cheap, Don't hurt your motor, Stop the small amount of movement that can cause a crank to fail then blow up your motor. Cases, topend parts cost alot why risk it?

Ducman Over the last year a half building my knowledge base of Banshees I think I read banshee are in the neighborhood of 12.8 air to fuel ratio. But remember use that with care.

why not a New Post Bans

No Kehiens for me I am a Hard nose Mikuni fan .

Ducman Do it and the do a review for all of use .

Look At Banshee370 website. T3 Cutting

AS Anybody ran Mikuni TMX 35mm Carbs on the Shee. If you have what do you think of them. was jetting a pain or easy did you like the way they works? Problems? Pro's And Cons all welcome? I am thinking about my letter to Santa and i am torn between them & the Vm series Proflows that are bored 34mm to 35.2 in the right & left set. either set will work well with my 35mm intake manifolds.

Rod did you try my recipe on page one and what did you think?

Tats Nice looking $5 I answer you pm here ok. It was bought. it's a Charles Daly Its a cheaper pistol but it well biult for the money it had lot of feature add in to start. Bevel mag hole lighten trigger & hammer, ext beaver tail ext slide lock and ambidextross Safety and few more I did install a Hogue Mono I love them hogue rubbers. It will swap parts with a kimber, Friends has on and we played around one night. Pretty tight barrel & lug also. But for 345 dollars + the 20 bucks i paid for the grip I think it was great purchase.

Here is a pic of one of my pistols I aways wanted a 45 acp.

He Open alot of public ground to ride on with your fruggen Banshee on. He kept the Anti Gun faggits from take your shit away. He also Fucked your SS and Heath all by hmiself, in 8 year Fruggen Cliton Didn't do any thing make the Ecomony any better. Ragens plan started to fix it the Bill got his Cigar wet. All you you Closed mind Dem think Bush screww it up in the first three days in . WHere you even born yet?Gezzzzzzzzzzzzzz Man Kerry is a Stuck up SoB and he will pad his own palm You can bet On that.Promise I promise I promise.

Could you weigh them ? if there lighter than stock you may have a repete customer.

I am running some Old school Artic cat pre Vm model round slides I am little rich 1/4 to 1/2 throttle in hot weather at 4300 feet. 270 mains 1st clip needle 6dp17 ( rich snowmoble ) need to change for a leaner one. needle jet Don't know. 35 pilot slide is 2.0 Little rich But i still to test that. hope this helps

Daviid what do your tiierods weigh.

I am a senior citizen. During the Clinton Administration I had an extremely good and well paying job. I took numerous vacations and had several vacation homes. Since President Bush took office, I have watched my entire life change for the worse. I lost my job. I lost my two sons in that terrible Iraqi War. I lost my homes. I lost my health insurance. As a matter of fact I lost virtually everything and became homeless. Adding insult to injury, when the authorities found me living like an animal, instead of helping me, they arrested me. I will do anything that Senator Kerry wants to insure that a Democrat is back in the White House come next year. Bush has to go. Sincerely, Saddam Hussein

I wonder why 200 rifle shooting is boreing? : BMG Big mean Gun? Muhheheheheeee Nice Land cannon. 2500 yard Shot, Carlos Hatcock (Sp) Could make them with that cal. What is the guns weight?

Nightrider I new the answer along time ago I just didn't want to come across like a Ass. I was just try'in to enlighten you. In Utah most of the 90% of open ground is BLM & national forest land. So you quote was only 10% true where i like. You would make a Great President.

dnhyoung Look into the new 17mach 2 round have you seen it ? Cute little bastard of a round 2100 feet per second little slower than the 17 HMR . But i bet i will be cheaper too. Tats you into Pistols?

Well the federal bureau of land management runs most of the Dunes & deserts.

Tat's The Barrel Is a Adams & Bennet with a Benz chamber. With a biult in Wheeler Muzzle brake. It redirects the gases for a more stable 2nd shoot. I finished the stock was a 95 % inletted Fagen Spent 3 weeks sanding ,sealing and the 8 coats of Tung Oil handed rub in.I did all the work including the valquartsen (Sp) trigger mods, exracter etc... Tasco Target 6x24 power AO. it will touch all 10 rounds a 50 yards.

Nightrider Is the BLM State ran or Fed. What about a National Forest?

The T5 Reponds Better and Better is Better. AS far as looking for a % of how much more from minor to major Porting does. No one could tell you with all the varible that one can change How Much Better. Get a pair and test them, then tell us.