Oilsmoke

how much of a swinger you looking for? Looks like a fun test. But i only make the dunes a few times a year.But i am also in need of a rear rebiuld. If that is enough time Pm me. I am also a Old timer so i am some what lesser than agreesive but Still enjoy getting On it.

I was in a chat with Mp350 and I don't think Dave Moore is Dune Gooney. they where partner in MP racing. They split up according to Walter.

Should be a Good race Let us know who wins. Cheetah Cubs are after market cylinders. Cubs and T6 are not your best combo.

I like to know this also.And what would the cost be for a bare unfinished set?

LOL well I don't believe You or your claim.

Thx for the info Wesw Time & money spent. SO how many pulls did you do?

Jim that looks great. What where your Jetting Spec? And tenision setting on the V2? What type porting did you set them up for? I wondered when i bought my Shearers if it was a good choice Being the test bed for this combo. I was never sorry i took this route

About 27cc"s

I may take a jug of your hands for the right price. Front plastic is a maybe too.

Thx for the Spell Check Your Right RedNeck Bullshit sounds Better Nobber Muhehehehe The point is Both Carbs Work Great when Jetted Correctly. It's the Jetting that make the Power Output what is can be.

Personal this is Very Bias statement. Out here is Dune land & Planet sand Forum. A lot of people Run Mikuni's Most Winning Drag racer Use The TMX or TMS for a winning combo. K&T a world wide know Banshee biulder Uses Mikuni, SO I'am not listening to your rederick Biased Bullshit. Like he said if you want more power from a Stroker Cub I would use the tms 38's Keihin are for Kids Mikuins are for champs.

This yeilds 8 inches so 6 to 10 is my range. for quad placement 10 is the best but i need to watch my tongue weight so if 8 will work i will go with that. Thx all for the imput and Quad4me for plans link

Well 60 percent is 57.6 inches. Almost 10 inches. Past halfway of the main frame. Sound like good place for it. IDAHOSHEE I am not an engineer How would I calculate that out? Loaded or unloaded? It will haul 2 quads about 650 pounds plus the trailer weight. So my tongue weight will be fairly low quessing around 375 with 9 or 10 inch past centerline placement. Is this Ok

If thet where yours you would know. Lamer.

I have a single atv trailer. It's over biuldt big time. It's made out 3 inch channel. My plans are to widen it to 6.5 and lenghten it to 8 feet. So it can haul 2 quads sideways. WHeel will be outboard of the frame. SO where is the best place for the axle centerline? any tips guys

K&T Performance, PassionRe And most people Hear don't run them. take them out and Never look back.

Sanddragon did you try the one i posted?

The Boon Tune is The first thing I would DO if i was starting a New banshee. Did you mill the head?

CEJ Missed one Advantage COST. they are lot cheaper to Purchase, install, operate. the Low Humidity Summers of Utah 5% to 15% The added mositure is very welcome in my house.

Broke You are telling me you Never See or Heard the Term Swap Cooler? Man that's just wild. Stan I just installed mine in the Kitchen window 1 1/2 hours. Muhehehehe

Ducman Thx for your view. The St Anthony Dune is ALL HILL AND Open Dune ANd the Cubs would Plain SHINE there. I ride mostly 1/2 to 3/4 throttle when on the open dune & 110 percent Hill racing. But i am still very happy with my 12 port stroker. Disclaimer I posted this Thread as a Joke. it's Not my fault. Lacgoto No way My dad eats rebar and shits nails

I just got this a few minutes ago. Speed150 new email atvspeed1@sbcglobal.net

10 paddle Sand sharks? I didn't know them made more than 8's I would get 8 paddle Hauler in 21x12x8. Great do it all paddle.

Whitey Welcome to the HQ

Whitey Here is a few questions. What type of Port layout will you use with a Forced induction? Is some form of expansion chamber even needed to scavenge the exhaust? was that ecu a kit and who make it? It look like a Fun Project .