Tedder

The washer clearence should be fine with 2.86 ratio but it's worth a look. Through the years I've run a total of 12 TZ bearings in my asphalt bikes and never had a new one make any noise when spun. Straight cuts can make a little more noise than stock but not "terrible" as you describe. Don't hear mine over the OOF drag pipes lol.

When you went to the straight cut primaries did you change to 2.68 ratio? If you did then I'd check the thick washer on the water pump shaft. The oversize gear will rub that washer and make a terrible noise. You can carefully grind it down for clearance. Another thing that you might not be aware of is that you need to use a little silicone sealer on the crank key or slot so air doesn't get sucked in causing a lean condition in the right cylinder.

Pic sent. Let me know.

Send pm with an email address

Bought from FAST Racing - Installed on wifes bike then immediatly removed - Never even hooked up the cable. Her hand is to small for the reach. $38.50 shipped to the lower 48 only

Like it says, Looking for an AC Grab Bar in real nice condition for a Banshee. Thanks

Can you just put a rubber plug on the nipple in the clutch cover or do you have to bolt on a block off plate? On an asphalt bike can you leave the pipe off the back tranny vent? Thanks

Both me (53) and the wife (55 in June) drag race 1/4 mile asphalt Banshees.

Hi Pat, Like I said in the pm I've only used Wilburns (currently own 5 of them) which I love but Dyna's will do the job also. SlowerThanYou can help with your Dyna questions. We've killed cell phone batteries more than once chattin' about racing. lol

Sold - Thanks

Sold - Thanks

Pics sent

Hot Rod. Updated the description. Thanks

*BRAND NEW* - 60 or more individual clutch fibers that I had custom made by Barnett for one of our asphalt Banshee's The are constructed with RQ (organic) material. Very durable and heat resistant for consistant ET's but do require HD spring pressure. I paid $14.62 per plate as a special order and can provide a copy of the invoice. These should be run with an inner and outer Kevlar fiber to protect the aluminum pressure plates. Price of $7.50 - $8.50 per plate based on how many your interested in or if a "kit" is wanted with Kevlars/springs etc. PM me with what your interested in. ** 8/23/18 update - I also have 6 or 7 full sets of fibers that are the 2 Kelar and 5 RQ's as the original Dirt Digger's were.

2 brand new clutch basket bushings. Just like the factory Yamaha bushings (bronze over steel) $23.95 each shipped to the lower 48 only

Dual feed Pingle fuel valve. Part #3110-D-A4H Is new but was mounted. Comes in original package with gasket & instructions *Filter screen is removed* $70.00 shipped to the lower 48 only

Ran 2 seasons on the asphalt. Stock Stroke Hot Rod crank Trued and welded Included are the 2 original never used outer Hot Rod bearings *Does not include any wrist pin bearings* $135.00 shipped to the lower 48 only

Boubin Tire Here you go: http://americanracertires.com/

PM sent Professor.

Terrific communication and true to his word. My parts were exactly as stated and at a SUPER price. Less than great dealings in the past have left me gunshy on buying used but this deal was A++ Cals an asset to HQ and one of the good guy's for sure!

Paypal done. Sent shipping address in a pm. Mysterion, Thank you - Very noble of you to not jump at the chance to snatch the domes out from under me. Shows me what good character your made of . I'm in Geauga County. We race 1/4 mile asphalt, Mostly at Thompson Raceway Park which is 12 miles from our home with an occassional trip to Quaker City and Dragway 42.

Thanks for the reply Are they just standard Pro Design domes? What condition?

Looking for (1) good 19cc Cool head dome.

NYUK came through for me again. Stand up guy for sure.

Good choice. Thats the trans I use.