Jump to content

23champ

Members
 View Profile  See their activity

  • Posts

    853

  • Joined

  • Last visited

 Content Type 

Everything posted by 23champ

  1. 23champ
    So does Dan Hull
  2. 23champ
    I pulled my hotrod 4mm out after about 10hrs of hard ridding, and discovered that the bearing stay pin on the waterpump side had came out. I don't know how, but it did. One of my O rings was torn also. Needless to say, I havent had the best of luck with mine. Hope everyone else's holds up better than mine.
  3. 23champ
    boyseen is a dual stage reed. The reed blocks are not needed any longer with the boyseen kit.
  4. 23champ
    I heard JIM SMART does pretty good work
  5. 23champ
    I say stick with the 13, Throw some 22x11x8 9paddle haulers on and smoke his ass. Don't let your dad do anymore porting on your cylinders. Unless his name is DAN HULL.
  6. 23champ
    TWENTY BUCKS!! IT'S CHEAP INSURANCE
  7. 23champ
    I've heard Padla Brats are the new thing now. Comp cuts are extemely light. and hook very well, and the tire is more rugged than a ultra light hauler (not as prone to leaks,and the paddles wont rip off). Sizes are 21x12x8 or 21x12x10. I saw a set last fall at LS, they ARE a bad ass tire, but a bad ass price comes along with them!
  8. 23champ
    Ladies and gentlemen,.... the first banshee ever to hit 14,000 rpm!
  9. 23champ
    Are you fuckin kiddin me? BUSTED!!
  10. 23champ
    Does it load up and smoke real bad when you're just putin' around? If so your pilots could be too rich
  11. 23champ
    Who ported your cylinders? If this guy can get 93hp out of a 4mm, with 28mm carbs, and runnin on pump gas, I need to shake his hand (for being a bad ass).
  12. 23champ
    Thats pretty sick dude!
  13. 23champ
  14. 23champ
    They've always hooked me up with no probs. Great place to order from if you ask me. Plus they have a lot of shit, so when your ordering a bunch of stuff you can get it ALL from them, and not pay shipping from 2 or 3 other places.
  15. 23champ
    If you didn't line up the water pump gears when you put it back together you may have knocked a few teeth off the plastic gear.
  16. 23champ
    Thats probably the price for a single cylinder quad. Banshees will more than likely be more expensive.
  17. 23champ
    I'd like to hit it on my CR500 too
  18. 23champ
    yeah, I pulled the cylinders about a week ago, they should be to there destination by now. I gettin ready to call him right now to ask him if they've arrived. By the way I heard through the "Grape Vine" Charlie isn't runnin quads next year. I guess Travis's little spill over the first jump freeked him out. Charlie's a homo.
  19. 23champ
    If it were a drag race, I don't think the cpi's would have an advatage at all by coming on 500 rpm sooner. I don't know about you, but when I'm dragg racing my motor is far from ever touching 5000 rpm. Loco, I'm pissed. I just ordered a set of CPI's last week.
  20. 23champ
    I will have to agree, Yamaha has a PISS POOR design for the chain tensioners. Acually the whole damn swingarm is a heep of shit if you ask me. The thing must weigh in at 20 lbs... I feel your pain bro.
  21. 23champ
    Didn't know there was such a rave about them. They look cool tho.
  22. 23champ
    alpinestars are the best boot you can buy in my opinion. They're all I've wore for about 12yrs
  23. 23champ
    Where did you send your 500 motor to? I been thinkin about stroken mine. As you know I'm Gonna have to tear my 500 down to put new cases on it, and while I'm at it, I might as well go ahead a sink another grand into it. Do you have yours back together yet? I bet it'll run like a basterd!
  24. 23champ
    Loco, where is this place with the dyno? I might be willing to drop a little cash in on this deal to. What happened to Cario, I thought he was doin your work? Who ended up doing your cylinders?... Was it Garrett? If it was, it oughta run pretty good. I've seen some of his shit go, and its pretty fast. ED
  25. 23champ
    You don't like the rockets?

BHQ Quick Links

×
×
  • Create New...