sonnydlt Posted March 11, 2005 Report Posted March 11, 2005 Hey was just wondering what everone has for mods. on there shee's and what they dyno'd at. im takeing mine in sat. to see what it has for hp with just the bolt ons in my sig. was thinking on bigger carbs and maybe a port job but i dont want to lose any of my bottom end. any suggestions would be great help. hope this helps everyone get a sort of guide line to what mods. make the bigger hp. and maybe help someone else out too. Quote
ssanddemon Posted March 11, 2005 Report Posted March 11, 2005 I'll be interested to see what you are putting out. Not many guys dyno'ing the lighly built motors; it would be nice to have a comparison since so many of us guys are right in the same build range as you. I race a buddy of mine all the time who has almost your exact setup, and since I have been kicking his ass lately, I will add a few hp and be right in the ballpark for my motor. Please post the sheet if you have a scanner, that would be the best! Quote
fastbanshee4u Posted March 11, 2005 Report Posted March 11, 2005 Hey was just wondering what everone has for mods. on there shee's and what they dyno'd at. im takeing mine in sat. to see what it has for hp with just the bolt ons in my sig. was thinking on bigger carbs and maybe a port job but i dont want to lose any of my bottom end. any suggestions would be great help. hope this helps everyone get a sort of guide line to what mods. make the bigger hp. and maybe help someone else out too. 337336[/snapback] Get a mx port job just dont get huge carbs. stock or 28mm are all you need ,unless you build a huge motor. Quote
Mxracer776 Posted March 14, 2005 Report Posted March 14, 2005 i had mine dyno'd and it has 47.47 hp and 28.56 torq.my mods are in my sig.my dyna fs was set on stock setting and it was on prem. pump gas.i hoping to get it dyno'd again some. Quote
sonnydlt Posted March 14, 2005 Author Report Posted March 14, 2005 hey guys, well took it in but the clutch was slipping so i couldn't get a good reading so i was installing a new dirt digger and noticed the center slack adj. nut for the rod was stripped. so i drove 150 miles to find one. cause i wanted to get this done. anyway i got it done she pulls real hard now but i think im going to have to change my gearing back to stock cause now i can hit all 6 gears in less than 50 feet (12/41) anyone have any ideas on whats a good one for the dunes i also do alot of hill climbs. my buddies are amazed at the hills i can climb with it. ill get that dyno done this week and let you guys know. Quote
locogato11283 Posted March 14, 2005 Report Posted March 14, 2005 mine has 77.4 hp and 47 ft lbs of torque. Quote
madkaw Posted March 14, 2005 Report Posted March 14, 2005 mine has 77.4 hp and 47 ft lbs of torque. 339051[/snapback] What was done to your banshee to produce those numbers? Quote
Big Blue Posted March 15, 2005 Report Posted March 15, 2005 mine made right at 70hp and 35ft/lbs of torque. Quote
locogato11283 Posted March 15, 2005 Report Posted March 15, 2005 What was done to your banshee to produce those numbers? 339060[/snapback] high performance powerbands and lots of sticker... jk, its a 4mm stroker with a drag port.. Quote
stclark816 Posted March 16, 2005 Report Posted March 16, 2005 Mine made 85.1 HP and 47 ft lbs of tourqe. Quote
PUSH THE THROTTLE Posted March 16, 2005 Report Posted March 16, 2005 I haven't dynoed mine but if I add up everything correctly I'm right around 304.732419867HP Quote
madkaw Posted March 16, 2005 Report Posted March 16, 2005 Mine made 85.1 HP and 47 ft lbs of tourqe. 339850[/snapback] What are the mods to get that kind of #'s? Quote
sonnydlt Posted March 16, 2005 Author Report Posted March 16, 2005 (edited) o.k had mine dyno'd yesterday with just bolt on parts, no internal mods all stock it made 50 hp and 34 ft pounds of torgue. not bad for not haveing any port work. il post the dyno sheet when i get a chance to scan it at my bros. im going to run a 13/ 41 for the dunes with sand stars. p.s anyone know where i can get some info on the eric gore woods porting? Edited March 16, 2005 by sonnydlt Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.