n2otoofast4u Posted December 11, 2013 Report Posted December 11, 2013 New.... http://www.snowest.com/forum/showthread.php?t=359026 Quote
trickedcarbine Posted December 13, 2013 Report Posted December 13, 2013 JEEZUS green! Those are huge! Quote
n2otoofast4u Posted December 13, 2013 Report Posted December 13, 2013 JEEZUS green! Those are huge! Thought you wanted to go fast... Quote
99michael Posted January 23, 2014 Report Posted January 23, 2014 (edited) Lol, they say as early as April now for my 36 cast. I preorded back in April. Hahaha, oh well. Don't know if I like how the cable hooks into the slide though. Other than that. Seems fine. Edited January 23, 2014 by 99michael Quote
trickedcarbine Posted January 23, 2014 Report Posted January 23, 2014 Weak! Tell me to get you your dinero back and that you would be glad to put it back in their hands in April. Quote
sangheraent Posted February 18, 2014 Report Posted February 18, 2014 guys on the 250r forums just got there cast 38mm carbs in recently. Quote
willaduncan Posted February 21, 2014 Report Posted February 21, 2014 We need some feedback on these I couldn't fathom spending 700 - 800 but curious to learn of their functionality Quote
99michael Posted April 18, 2014 Report Posted April 18, 2014 Said they where gonna push the cast 36's back another 6-8 weeks,, so they FINALLY gave me a discount for the billet,, hope to have it installed this weekend.. Fingers crossed.. Quote
Strm Trpr Posted April 18, 2014 Report Posted April 18, 2014 ^^^ You bought a dual set-up, right? Quote
99michael Posted April 19, 2014 Report Posted April 19, 2014 Nope,, I only have a stock cylinder mx port, an exciter intake, and pt mids.. I think I'll be fine. Not too worried if it fails either,, lol, should be fun. Quote
03DMshee Posted April 19, 2014 Report Posted April 19, 2014 Just read whole thread...dont know how I missed it this long...through the pages I hated the idea...then I liked it...then I said fuck that...then I said maybe...now im just interested in how well it works... Quote
99michael Posted April 19, 2014 Report Posted April 19, 2014 Well, I got it on,,lol,, First it was kinda a tight fit in the intake boot.. Which I kinda expected. Next went to fill up the bowl for the first time, and it started pourin out the needle opening. So shit, i set the float adjustment a little lower. Came out at about 18-19mm to the top of the bowl an seemed to be fine.. Next,, my cable didn't let the slide close all the way.. So shit,, figured I'd be fucked till I got a cable. So I researched a little, an seen people had luck with a cable that had the 3rd adjusters on them. Which I had one on my cr250 w/ a thumb throttle.( think its a 250r cable), so I put that on an that solved that issue. ,, Finished putting on the pod, and tried to start it. Would not fire, so I figured I must of flooded it out when the gas came pourin. So I pulled the plugs and sure enough they were wet,. So I kicked it over a few more times then through the plugs back in. Then she finally fired up a couple kicks later.lol,, at first it would barely idle, but I'm pretty sure that's just cause it was flooded. After it ran for about 30 seconds it idled fine. I think it's still a touch rich yet, but sure does seem to run better than my pwk did. Will have a better impression once I get some more riding in,, but so far so good. Also,, the throttle is really light. Especially with the Honda throttle.. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.