rdzbangshee
-
Posts
349 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Store
Everything posted by rdzbangshee
-
i like the t6 pipes must be a detuned dragger
-
Shee leaks gas out of overflow tubes
rdzbangshee replied to 2002SHEEownr's topic in Banshee Repairs and Mods
i have a couple sets of stock carbs that dont leak i went to pwks ill give them to you for nothing the last four sets of stock carbs i tossed in the trash -
break out the card and run it wot tell you do it again i do it tell my engine is in the trash every time its inley4 grand for a engine hun nana
-
ebay was the best fuk of my life live snd fuk up im a fuk to
-
my bro rebuiit with new carbs cylinders and it ran like shit overheated and lost compression hes going to rebuild it the same way again with some new pistons man i feel like slapping him lol hay i get slapped all the time haha
-
will they work with a hemi head my mod quad domes leak bad out the plug tops
-
mine was the same i just featherd the shit out of it then i i did a 1000 $ rebuilt on the top end its all good now dont slip at all
-
mine did nit have a crank washer in it it made the crank bend i got it used it tore the engine up when i rebuilt it piston slap and blown bearings sheared the flywheel of and tore up the cases
-
what carbs you got could be a plugged pilot
-
ill talk to rob .i no what do do now jest need to make sure i use the right o-rings on the cool head 3rd times a charm.
-
ya well i got mine from vitos on the right exaust port the right cylinder looks like it had a clean up port but the left had huge casting flaws in it ill have to get them port cleaned and matched up for a rebuild and repalate . thanks guys ill have to talk to rdz about my bad cylinder for a repair .
-
my bro had someone weld his up like new then he sold the bike for a bag hehe
-
it should be rich like one turn out one the air screw third clip down from the top on the needle and a 320 main with the stock needle i run 28 to 35 kiehins and i run a 55 pilots on the forth clip with 180 mains its good to be blubbery rich if you dont want a melt down in a heart beat you dont want it to sound like a 50cc zingger
-
-
i want cylinders that run wot out of the box i am willing to spend another four grand and i get nothing but negative comments on the help of it most you say i got a pile of shit and i get pizt off easy help me i am stuck with these eliminator cylinders and they are junk with melted nikasil
-
it would cost me 9 grand to race 9 times what i was told
-
no instructions i red neck my stuff all the time o would sen it back for a new pipes they screwed you
-
i was told to run a 450r radiator in the cold on a banshee in the cold ice weather
-
you should run it a little fat on jetting enough to just feather the clutch but i run a duel taper needle on the 4th clip rich and crisp top end
-
just take it easy on the stock crank it breaks easy under a load and overheated bearings
-
looks ok but i like to run 60 pilots and needle on the 6th clip and 200 mains in my sudcos to see if it blubbers and run no less than 95 octane gas to be safe .
-
i have 120 hours on my vitos crank and im going for another after i rebuilt my tip end ill let you no when its junk
-
what transmission oil you guy's running?
rdzbangshee replied to chetgoff's topic in Banshee Repairs and Mods
i like the stuff thats made for two strokes -
bad boy racing does overrides the say its go for any thing
-
i just slapped some .50 over stock juggs on my 4mm stock rod stroker but i only burnt half a gallon of gas its to cold to have fun on the ice for long it lean now and has allot of compression just need to jump up the jetting to make it run good without burning it up