fastrthnu

I have (had) a ported 4mm motor making just under 80hp on a -2. Yeehaww!!!! :cool: Just dont plan on drag racing on any hard surface or you grab bar is going to be PISSED.

are you talikng about the drag strip in immokolee? big cypress mx?

yea, put it together an warm it up and test with the pipes on and the carbs all the way open. The back preasure from the exaust and warm piston(piston expands with heat) should make better numbers.

Looking for a pair of wiseco pistons to match my +4mm hotrods @ 65.50 (.060) new or in good reusable condition.

no job. I still havent been paid in full, and if I dont have by this Friday, Im going to go ahead and sell everything.

need to get a myspace password. I have the email address, just need to figure out the password. PM me.

Sold this morning, my sisters bf put a $500 deposit to buy the whole thing.

Older pictures from the MX track... notice the cool pearl paint from green/blue/purple. if my shit was running Id go out and get some good action shots.

yes, these are 30mm mikuni roundslide carbs. these filters and outers where used 1 time, but one of the outers has a small burn hole in it. they are dirty for use, but I can provide you proof they where just purchased off ebay. the rubber spacer and pipe is an adaptor I made so these would fit my stock intake boots. Ill send the whole set for $150.

yep ALSO,, I just got an offer for the whole thing. So Ill post an update tomorow if its still on.

Parting out this entire quad. I think I blew a piston on the left side. 150lbs on right 30 on left. Parts so far are; 9" hiper beadlocks with mxr6 holeshots 70% rubber. $375 shipped +4 g force axle $175 shipped front douglas black with 85-90% tread on tires some dings $85 shipped elka piggy back dual rates $675 shipped +3+1 a arms with fully adjstable heims with matching extra thick tie rods. $425 shipped stainles steel front brake lines for +3 arms $30 pair 30mm roundslide mikuni carbs $100 shipped pair pods and outers 1 day use listed for 33, 34 , 35mm carbs $60 shipped I used these on these 30mm carbs. asv clutch lever with cable $35 shipped -2" swingarm $200 shipped rear carrier $25 shipped rear hubs $25 shipped seat 2 available ask for details $40 shipped rocket pipes and silencers good shape $350 shipped rear shock $35 shipped frame $350 shipped front brakes calipers spindles hubs $60shipped ac propeg nerfs $125 shipped the motor is a passion racing 12port 4 mill. RZ 385cc I will be selling whole or parted out depending on what I see when I pull the head. I may sell it whole with electronics, or part it all out. Once I get it out and look at it Ill put it up. The motor runs. But the compression is way off and may have blown it wot in 6th running out of gas. Pm me if you want my number.

yeh those are fine for regualr trail riding, and $420 is a cheaper price from what they normally go for too. Plus Im pretty sure you can add a res on later if you wanted. works shocks are great, esp over stock, but nobody beats elkas.

stock vs stock the lt500 barelly beats a banshee. It should do more than that being 150cc s larger, but it was poorly engineered. That was done in dirt wheels I think when this pos that only lasted a few years if even was new to the scene. The lt might have a little better over all handling, the banshee was made for baja. People cant give those things away around here. 2nd why are you on this site and where do you live? All banshee owners are losers? I hope you say you live in FL. Little bitch ass faggot!!! Id bust that fuckin tl over your face.

I have a passion 12 port rz 4mm and it runs pretty hard. I thinl Id hit 80hp or damn near close.

I got one from the swing arm shop on ebay and like it. was like $200. great welds n fitment.

I was interested in trying these, but I think they will choke my motor too. I have rockets which are comparable to cpi.

I think ive been there in north port as you goin north it right on the right hand side of 75 right? dade and broward suck for riding. even off 27th. when I lived over there I drove to bonita every weekend to ride.

pff. you have good feedback because no one who leaves bad wants to receive it. Ive gotten about 5 items off you and most was bullshit garbage. The last was a set of hubs with a broken off stud. what the fuck is that!!! I left neutral feedback and then got the same. All I did was fucking pay right away. Just because you sent a replacement stud after I bitched doesnt change the fact you send broken fucking garbage, and I had to sit out a weekend and wait for the stud. Fuck you. A coil with wire just pushed it and pulled right off, carbs with one of them having stripped tors threads. If I part out a bike I dont sell the bs parts, I give them away or throw them away not sell them. Less than half of what Ive gotten was good. The only time you even visit this site is to advertise your shitdick garbage.

I race all mx and gncc and once in a great while TT. go to big cypress. I go out with people att the time and set up races down her between lehigh and bonita springs, actually starting this weekend. Ill be makin a few trips out to race the track too after new years. I used to ride air dania right after it was shut down all the time. I dont know of any mx tracks in miami. I think moroso doesn supermoto sometimes.

Everyone is going to tell you a few names. I have a passion racing 12 port job and it is great. about 6-8 more names will prob show up. $250 isnt alot for a good port, its actually well worth it.

used to race out off 27th , moved to the west coast though. I have heard of 99 performance, but dont recal the feedback. I always used TDR when I was over there, but he moved west as well. There are some good 1/8 races here in immokolee. I wasnt a banshee racer as far as drag, but seen alot there racing cars.

slack up your cable at the perch, drain your coolant and oil, pull the cluch cover off get a wrench and phillips for the adjustment in the middle of the preasure plate... press against the actuator lever till the pointer on it and the pointer on the case line up then set the adjuster in the middle of the preasure plate ..... then re adjust the slack back out of the cable at the perch. your welcome.

If mine was of equal value , I would make the trade simply bc those 250`s are great 2 stroke quads, and rare. I could always build another banshee. There are only 50 gazillion of them around. The only prob in my case would be another rz setup, but if I did it again, I would get some trin pv cylinders so it wouldnt be hard. That is a nice quad. Take it for a ride.

turn your air screws in a turn or so and see if it improves at all