trickedcarbine

It's possible that 370 is a bit fat. What do the plugs look like, and what race gas are you using?

Look real close on it for any raised markings. There should be a manufacturer marking.

Chariot intakes have real mikuni boots. At least in my experience.

Oh, my bad. Didn't realize things were so cool between you two.

Isn't that Ryan and Brett? This their confrontation?

Rebuild the master, or get a new 450 set up.

So much work and it'll never look right. I would take it and blast it, and have it re powdered. If you are adamant about pursuing this paint removal, I would continue with the goof off. Buy the big yellow gallon jug and a small hand sprayer. Spray a fine must over it and wipe what you can, then for the books and crannies, spray it and let it soak. Then try pressure washing it.

Tech Care. If I had a bike I'd take it there, but to do anything custom on an atv shock these days.... Nah. I suppose they are competent enough to take it apart and put seals in though....

BansheeDepot = TDR

Look right underneath the rear motor mount. There will be a little plastic press in vent port. Inspect all that. Take the hose off. Verify that the little plastic elbow is not clogged.

Cooling jackets. Bluebanshee98 has a quasi trail bike with a DM and it may be worth shooting him a message and asking just how much riding you can do before needing to cool down.

It's possible the Crank case is not sealing and pressurizing the gear box. Pop the vent off the rear, not just the hose. Look in the hard plastic part fr trash. If nothing, verify whether or not the crank case is sealed up.

Possible. Was it blowing smoke out of the right cylinder? And did it keep flowing after it was off? That would lead me to believe it's a heat/vent issue.

NO NO NO NO NO NO NO NO NO! Those guys are the brick weed of quad suspension. Nobody knows anything about quads anymore. If you got a two wheeler, by all means go check them out. But to them, anything with 4 wheels is a nuisance.

For what those pieces of shit cost, you can find really nice quality used shocks that are actually intended for your machine.

This thread was not intended for people bitch and complain about the same sellers that already have 100 complaint threads. It was for a vender to inform other vendors of the short comings and complications of using EBay after policy changes. Please post personal shit experiences else where.

Yeah, usually those are hard to get looking nice, but he friggin nailed it there.

Well, it is a cylinder. For a honda. It has a similar bolt pattern for the reed cage. There are boost/auxiliary/boyheson ports. Hell, I'll bet they both take a piston........ Haha Seriously, I think I see some vast differences in the two. The ESR takes the contour for the auxiliaries all the way up, but IMO it's kind of a really lazy contour. I'd love to throw smoke at it to see what the air does up in the upper corners of the intake. I bet it kinda runs in and does a few cyclones and slows down and sorta limps it's way back down to the auxiliaries. Normally I'm not in to knife edged shit, but I see how you are working the angle there on your's and that set up works on the Hondas. There is some real velocity being created there with low turbulence.

That hose is for trans/clutch case venting. It is possible that you have the rear vent plugged up or that it is getting hot enough to cook the oil.

^ kaboom!

Go through the website and make a list of everything you want or can't find( they carry double what the site shows ) Call, leave a voicemail. Jeff or Cody will call you back within a day or so at most. Run your list by them and wait for mega package.

No shit? I was always under the impression they were family. That's a trip.

Find Tom Borrink on Facebook

Haven't got to drive them through a winter yet. A buddy with them says "They are siped enough to not slide around unless you mat it, but they really do awesome in snow & slush". I've had mine in mud and construction areas and I friggin' love 'em.

http://www.foxillinois.com/news/features/top-stories/stories/jacksonville-shooting-victim-filed-order-protection-months-before-murder-4380.shtml Yeah, pretty fucked up. Right in the police station parking lot. http://thetelegraph.com/news/71230/shooting-victim-had-feared-for-his-safety Aparrently she was the "crazy" ex type. She definitely is the reason her father did what he did and because of her, those children will go with out a father amongst many other things. It's only a matter of time before they are removed from her clutches.