BansheeBoy347 Posted July 1, 2011 Report Posted July 1, 2011 Are these good cranks? Need some info on them because they are only $350. Here is the website http://cgi.ebay.com/ebaymotors/YAMAHA-BANSHEE-VITOS-STOCK-STROKE-CRANK-_W0QQcmdZViewItemQQhashZitem1c1b5a6c19QQitemZ120717995033QQptZMotorsQ5fATVQ5fPartsQ5fAccessories Quote
lesnant Posted July 1, 2011 Report Posted July 1, 2011 Are these good cranks? Need some info on them because they are only $350. Here is the website http://cgi.ebay.com/ebaymotors/YAMAHA-BANSHEE-VITOS-STOCK-STROKE-CRANK-_W0QQcmdZViewItemQQhashZitem1c1b5a6c19QQitemZ120717995033QQptZMotorsQ5fATVQ5fPartsQ5fAccessories Have someone go over the welds. I had 2 rides on the crank and i seperated. The welds broke on the pin. I wont buy again. I went with a hot rods on the replacement. I got ahold of Vito's and they said no warranty on the crank. Quote
locogato11283 Posted July 1, 2011 Report Posted July 1, 2011 We had a Vito's 10mm crank separate twice. I'd steer clear of them. Try one of the site sponsors for a crank. Quote
bansheesrtoys Posted July 1, 2011 Report Posted July 1, 2011 i wonder if viteos became a site sponsor how many people would change their minds about them kinda like trinty racing. as for their cranks i had two of them never had a problem with their welds. i'm going on 3yr on a +4 stock rod length crank right now from them. Quote
locogato11283 Posted July 1, 2011 Report Posted July 1, 2011 i wonder if viteos became a site sponsor how many people would change their minds about them kinda like trinty racing. as for their cranks i had two of them never had a problem with their welds. i'm going on 3yr on a +4 stock rod length crank right now from them. They did fix the crank after our first incident with it and sent it back free of charge. After the second time my buddy said fuck it. I don't think most people have changed their minds about Trinity as of yet. They just think it's a start that they have acknowledged a problem and are attempting to fix it. Quote
Angel ripper Posted July 2, 2011 Report Posted July 2, 2011 We had a Vito's 10mm crank separate twice. I'd steer clear of them. Try one of the site sponsors for a crank. bullshit. if they were a site sponsor, then your tune would change. Quote
BigRed350x Posted July 2, 2011 Report Posted July 2, 2011 I would get a hold of Kevin at HJR for a crank. His cranks are made in the USA and very nice & he stands behind them. Quote
jbooker82 Posted July 3, 2011 Report Posted July 3, 2011 I would get a hold of Kevin at HJR for a crank. His cranks are made in the USA and very nice & he stands behind them. Made or Assembled Quote
sprinklerman Posted July 3, 2011 Report Posted July 3, 2011 Made or Assembled Thats what im wondering...i'm betting assembled. Most of these cranks are coming from the same overseas "vendors", then the buildershere have to do make whatever changes thet feel they need to do, re-assemble and sell them. I dont have a problem with that ,,,as long as the builder is straight up about that fact. The site sponsors here are good about that and stand behind their products....wherever they came from. Quote
locogato11283 Posted July 3, 2011 Report Posted July 3, 2011 bullshit. if they were a site sponsor, then your tune would change. I bet if my dick was in front of your mouth, you'd suck it. Quote
Rotax Raptor Posted July 3, 2011 Report Posted July 3, 2011 Sponsor or not, junk is junk!!!!!! Do your research like your doing and the people on will help. Last weekend I had the weld break out of my 10 mil crank and basically shelled my motor except the clutch, stator side and tranny. It broke both cases and trashed the entire topend. Spend the extra bucks and save yourself a lot problems down the road. You have a way with words loco, that's some funny shit right there :-) Quote
bansheesrtoys Posted July 3, 2011 Report Posted July 3, 2011 X2 loco thats funny. but all i was sayin is that it seems everytime sombody post somthing about a motor it always say go to a site sponsor. Yes i agree they are good and helpfull, but they are not the only people that can build ,port,mod a trans, their are plenty of places that do a great job that peole hate on because they are not a BHQ site sponsor. and vitoes also found a problem with their product thats why they stopped plating their cyclinders so they are also trying to fix things.like trinty racing. To be honest i never used a site sponsor from here because i uasally find prices cheaper esle where, and evrything breaks sooner or later. Quote
toytech Posted July 3, 2011 Report Posted July 3, 2011 I would get a hold of Kevin at HJR for a crank. His cranks are made in the USA and very nice & he stands behind them. his web site says they are assembled in usa. vito's has fixed two problems for me free of charge. and bored my cyl for free to help me out. Quote
fastquad02blaster Posted July 3, 2011 Report Posted July 3, 2011 his web site says they are assembled in usa. vito's has fixed two problems for me free of charge. and bored my cyl for free to help me out. They are fixing stuff that's messed up for free but, why go through the trouble. Just buy a hot rod crank and be done. Quote
bansheesandrider Posted July 4, 2011 Report Posted July 4, 2011 Or go to Twister, last time I checked they were $350 plus the ride. I have never had a problem with a Twister crank. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.