ticktock

You need to open a claim with PayPal and get your money back. You only have 45 days for this. You have used 22. Get your money back and call A site sponsor.

It's prolly the KOC himself!!

Bling bling!

Does the topend have square pistons? Bump for a great seller!

On your carbs there is an air screw. Small gold left side of the carbs. On the left carb turn that screw in until it lightly seats (snug, dont tighten). While your screwing this in count the turns, normally this is done in quarters. Ideally you would like to be between 1-1 1/2 turns out. Depending on mods, your pilot jet could be too small. You can compensate this with the air screw. This will cause the bike to start hard when cold. You must adjust both carbs the same. I recommend counting the turns out and setting the carbs 1/2 turn in. Adam

I purchased some tires from decon. The bastard sold me Square tires. I thought the wheel was round!! Adam

Crank sold on ebay in the middle of the night sorry. Adam

last, last call! heh Adam

Added a couple manuals I have around. Adam

Fucking Troy, that bastard has alerts set up for the forsale section. This isn't the first time he bought good deals 5 minutes after the post!

Welcome to the Forum!! If your crank is still good you could turn that around on ebay and easily get 150$ for it. I currently have a stocker on ebay and there are 15 watchers on it. There is 1 bid, but I think the price is going to jump in the last day. I sold a different stock crank for 150 the second day it was up. So there is some market for stock cranks. Sorry to hear your bad luck, wish the best for you! Also talk with Kevin about your jetting, your pilot should be around 27.5 but 30 is rich. Adam

I have 28 PWK JJH Needles, new vent lines 215 shipped

Give Wildcard Racing a call, He can set you up with a great crank at an awesome price. He can get new billets, but he can build a 10mil Forged cheaper than a billet. Adam

You get outta here! Im trying to sell stuff with Chayote86 lol, Adam

My 2-1 was 58/170 EEK needle, one of the problems I found between two bikes, one being a friends, was that I had an airbox and this caused the bike to be Rich. you might want to try switching to a pod, I sold my buddy my airbox adapter and with the same jetting on his that ran perfect it was fucking up and too rich. Food for thought. Adam

I was running ATF, Lockup, FAST clutch. I think you might be tempting fate there, $40 is a good piece of mind, if you weld that shit up, its going to be 34 for the arm, 8 for the rod, prolly 3 for the ball and 40 for the bearing. Grand total 85 + shipping - But hearing someone's Misfortune because I figured I wouldnt need that shit, PRICELESS I made the idiot mistake, and it cost me. Adam

It wouldn't be a big deal but I have to have this on a truck Friday. It cost me 80 dollars for shipping on 80 dollars worth of parts. I couldn't do anything but next day air. Adam

If you need a manual you can DL below. Adam

Pancake Bearing: http://www.ebay.com/itm/Chariot-Clutch-Pusher-Pancake-Bearing-Yamaha-Banshee-Stock-aftermarket-clutch-/280866497251?pt=Motors_ATV_Parts_Accessories&hash=item4164f2a2e3&vxp=mtr Shift Shaft: http://www.farmandsandtoys.com/partdetail.asp?partid=247 Star Mod: http://www.ebay.com/itm/MULL-YAMAHA-BANSHEE-BILLET-SHIFT-STAR-GEAR-CLUTCH-TRANSMISSION-DRAG-SHAFT-/170830633036?pt=Motors_ATV_Parts_Accessories&hash=item27c64c984c&vxp=mtr Bearing Mod: Contact camatv, he will hook you up with a Drum to Bearing mod Adam

Here is the auction for the crank, its at 50$ on ebay, but there are currently 11 watchers. I am betting it will go over a 100 in the Last hours. You can take your chances or buy it for the HQ price at 125. Not sure you are going to find a good crank under that price. The big end play is .025 on both sides. I will wrap that shit so that if it gets thrown down the stairs the crank will survive! http://www.ebay.com/itm/221021712752?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649 Adam

I pulled the clutch he hit the brake. So not really at all, just didnt have the Pancake. Adam

I have a stock crank 125 shipped domestic, its a good stock crank. I have a complete clutch, but the cushions are bad in the basket, I could do 50? I have the crank on Ebay atm for 150 + ship if you want it let me know by tomorrow evening. The clutch basket has about a 1/4" of play, but the plates, inner and outer hubs are good. I might have other things if you find your missing them. Adam

Thumbs up Jared. You can do a modded star and shift shaft. If you do those two mods together then you shouldn't do the EZ spring or the roller bearing mod on the gear selector arm. Also the drum mod bearing. Make sure you do a pancake bearing. Saving 39$ is not worth the hassle you will get. Trust me. I just found out. Adam

No problem. Would you like me to get you a brand new banshee 2012 with 0 hrs? They still sell them in the middle east. Oh shit son, I can get 2012 plastics there at the Dealer and mail the home!! WTS banshee fenders cheaper than the add above!

We were in 3rd gear trying to establish a safe Air Fuel ration and the next run was going to be a WOT run in 5th. I was depressed so I didn't take a picture of the curve. The number I have shows nothing. Adam