Jump to content

BANSHEE HP

HQ Site Sponsor!
  • Posts

    1,807
  • Joined

  • Last visited

  • Days Won

    10

Everything posted by BANSHEE HP

  1. Die cast better than oem. Sent from my SM-S901U using Tapatalk
  2. You're in the back of the bus as usual Sent from my SM-S901U using Tapatalk
  3. Theyre 192° exhaust port. Kinda an in between'er but low 190's is what we've had good personal experience with. Its been super hard to keep the website updated or even add cylinder kits to it before they're already sold/spoken for with the parts shortages and the extremely long wait time on plating. Partially why we made a sleeve to install in our casting. All the labor of installing, port match, bore and hone is done in house vs sending them to plating at Millennium for almost 3 months. Sent from my SM-G965U using Tapatalk
  4. Were doing cylinders with steel sleeves now. 4mm stroke 64mm starting bore. Sent from my SM-G965U using Tapatalk
  5. I still call bs. Literally hundreds of ppl have bought cylinders from us in a year the exact way you say you didnt. Lane say hes left no email or voice mail unreplied. Good luck with bp racing Sent from my SM-G965U using Tapatalk
  6. I dont think you've called during business hours or left a voicemail. Sent from my SM-G965U using Tapatalk
  7. state side campsite #511 forsale $125 for the fall bhq ride
  8. if its a stock head that's what the squish is supposed to be … 2 miles. get an aftermarket head with interchangeable domes/combustion chambers.
  9. he'd have to go back in time 6 years to have langcourt plate his cylinders in the usa or send them to the UK where langcourt is.
  10. I did a 421 58x68 and a 424 64x65 this past season. The 421 made 2hp more than the 424. Ported very similar but I would say the 421 had a touch more work.
  11. correct, were not cutting oem heads anymore but we got deez drivelineperformance.com/yamaha-banshee-stealth-head/
  12. definitely, there are not many 424cc cylinders out there to begin with and this ones bad
  13. In the back, down into the rear jackets first, then the flow will come up the 2 side and 2 from jackets and find its way out Sent from my SM-G900V using Tapatalk
  14. 424cc 10mm stroke 65mm bore drag ported Assassin cylinders. 3 dyno pulls on these bmfers made 110hp with shearer small pipes and 40 pwk carbs on methanol. Will include cylinders, pistons, gasket, studs and domes (a head can be added also stealth or billet). $1100 shipped for bhq members. Sent from my SM-G900V using Tapatalk
  15. thanks, it probably is but its just what the it could make bolt on no dyno tune
  16. Drag ported 446cc Driveline Performance Assassin cylinders. Includes cylinders, studs, gasket, o-rings, 70mm pistons, domes and chariot super cub head. 110-115hp. The cylinders will be sent to Millennium for plating next week, you could expect them to be done by the end of November. $1400 Sent from my SM-G900V using Tapatalk
  17. never happen, new buyer is a tire kickin mofo
  18. it took me a over year to sell a set of stockers that I bored to new pistons and cleaned up the porting for $200. The junk ass Chinese cylinders that come with stripped holes, unlevel ports, unchamfered ports, soft ass steel sleeve have ruined the market.
  19. 100% there would have been a sticker and instructions.... shops that have bought our lockup in the past are buying the knock offs and still selling them as ours
×
×
  • Create New...