Poolman

I like your theory and how you think. If I was in the same situation where I had dunes around where i lived I would be putting on a 15 tooth front sprocket too. My God it sure is hard to read and concentrate on your post with that eye candy posing as your aviator. Is this your woman ? Frickin Gorgeous with due respect,

You could go with a 14 front and a 43 rear sprocket. With this configuration you would gain a little more low end torque and lose 2 mph up top. Or you could go with a 14 front and a 42 rear sprocket. With this configuration you would lose 4 mph up top and even a little more torque down low. Every 1 tooth change in the front sprocket be it +1 or -1 and leaving the rear sprocket stock at 41 teeth you will gain or lose 6 mph. Every 1 tooth change in the back and leaving the front sprocket stock at 14 teeth you will gain or lose 2 mph.

Once your jetted and synced properly you will have zero hesitation. For reference if this helps you at all I have Pro Circuits +4 Timing Stock airbox running k&N filter .020 Bore (Although does not effect jetting) MX Port Job VForce 3 Reed Valve System I'm running 290 Mains, 27.5 Pilot, and the clip is on the second from the bottom of the needle (Rich Side of Neutral or middle slot)

Yes Definately will get them pipes smoking the same. Since the Sync process can take a little bit of time (15 or so minutes) this is what I did to avoid overheating the engine. Put a Fan right in front of the Radiator and put the fan on High the whole time your getting the motor synced. Just another suggestion.

You don't use the air mixture screws to sync the carbs you use the Idle screw to sync while idling and the carb top adjusters to sync at partial throttle. I would start off by turning both air mixture screws 1.5 turns out. Get the bike to Idle decently, then start the sync process. The directions did come with the tool if I recall correctly or maybe it was with the tors eliminator kit but that's what I did and it makes a huge difference. Hope this helps !

X 6 Jeff bored my cylinders .020, Honed, Chamfered, and my bike runs strong. Very quick turnaround, I'm very Happy. Also If you guy's don't have that Sync Tool that Jeff sells I highly recommend it. I though I was good at syncing without it and to my credit I was pretty close at idle but part throttle forget it. I was off by quite abit. After getting the part throttle synced I honestly could feel a seat of the pants difference in power. If your reading this Jeff, THANKS !!!!!!

The Plastic's have been SOLD ! Thank's Everyone.

Thanks Troy, All PM'S replied too. New Asking Price --------> $230.00 SHIPPED ! , They are not going to be around much longer.

BUMP ---------> $240.00 SHIPPED !

I tried looking for a Roundhouse +2 Swinger with Carrier for awhile without success. The carrier bearings are bad in my stock swingarm and getting worse every time I ride it, so I made the decision to purchase new and Man talk about expensive for a decent one. I saw where Tyler suggested going with eyeball engineering with someone and that he had those swingers on both his bikes and liked them. Here is the one that I'm getting. I ordered it in Gloss Black and wanted skid plate mounts. The upside is they have a little special going where if you buy one you get a new rear Brake line. So that's what I did. Oh I also ordered a new UPP chain slider from them. My Grand total came to $775.00

BUMP -----> $250.00 Shipped.

I have decided to change the color of my Banshee to White. The Blue Plastice came off of my 2004 Banshee. They are in pretty good shape. There are a couple of stressmarks but nothing that you would'nt not want to showoff. These are the Original OEM Yamaha Un-Cut Factory Plastics. I ordered my White plastics through my local Yamaha Dealer and the closest dealer that had White OEM plastics was a dealership in California. Yamaha spent $98.00 to ship 3 of the 4 plastics from dealer to dealer and then I went to my local dealer and picked them up after taking 5 weeks to arrive. The 4'th piece of plastic (Radiator cover Piece) was shipped seperately which Yamaha spent another $16.00 to ship. So what I'm saying is I have no idea what the shipping is going to cost depending on who buy's them and where they live. I want $200.00 for the plastics and $60.00 for shipping. They will arrive at your door in a BIG BOX. I will have all plastic pieces packed and wrapped very well. I will also ship the very next day and send you a tracking number. I will only ship to the lower 48 states. $300.00 / Shipped My PayPal Information. paypal is: [email protected] send as gift or add 3% for paypal fees. Thanks ! Please include Your Name and Address and they will be in the mail tommorrow and I will send you tracking information. http://i910.photobucket.com/albums/ac302/Poolfixer/camping010.jpg http://i910.photobucket.com/albums/ac302/Poolfixer/IMG_0780.jpg http://i910.photobucket.com/albums/ac302/Poolfixer/IMG_0781.jpg http://i910.photobucket.com/albums/ac302/Poolfixer/M1110009.jpg http://i910.photobucket.com/albums/ac302/Poolfixer/M1110008.jpg http://i910.photobucket.com/albums/ac302/Poolfixer/M1110010.jpg http://i910.photobucket.com/albums/ac302/Poolfixer/M1110011.jpg http://i910.photobucket.com/albums/ac302/Poolfixer/M1110019.jpg http://i910.photobucket.com/albums/ac302/Poolfixer/M1110001.jpg http://i910.photobucket.com/albums/ac302/Poolfixer/M1110002.jpg http://i910.photobucket.com/albums/ac302/Poolfixer/M1110003.jpg http://i910.photobucket.com/albums/ac302/Poolfixer/M1110005.jpg http://i910.photobucket.com/albums/ac302/Poolfixer/M1110004.jpg http://i910.photobucket.com/albums/ac302/Poolfixer/M1110006.jpg http://i910.photobucket.com/albums/ac302/Poolfixer/M1110017.jpg

Yes, The choke does stay out on it's own whether it is on half choke or full. Jeff sells the choke assembly at fast for $20.00 I bought one from him 2 years ago and it still stays out but honestly they only last about 3 or 4 years until they stop staying out on there own. But what's $20.00 every 4 years right. And really if you don't care about it staying out then do like you have been hold out manually, kick until it starts and let the choke go back in. Really no big deal.

That's good advice. My trailers not enclosed. From where the two bikes will be parked to my bed is 30 feet. We will have the Bikes Cable together with thick cable and heavy duty locks. I guess we could keep the window cracked. I'm thinking some kind of sensitivity alarm strapped on each bike that will pierce the thieves eardrums if he set it off.

I cannot believe there is someone not making a keyed lug nut for ATV'S.

Damn Bro, Common Fuckers I really like your answer the best with the Blue Locktite. Thats Smart.

OK, Wash this a serious option or a joke, lol. I don't really know so I'm just laughing.

This is close to what we did last year but instead of the tree we chained our bikes together. Hell that Raptor700 is a Heavy you know what.

I will probably just put both the bikes on the trailer nightly. Much more inconveniance to the thieves..

LMAO, I just looked at Hub I'll just keep an eye on the Bikes the best I can.

Thanks Buddy, I think I'll roll to Autozone tomorrow and pick a tube up.

My neighbor and I go to Gilbert West Virginia for one week every year to ride at Rock House which is part of the Hatfield-McCoy Trail System. We have an absolute blast riding all day and getting drunk at night. We do what we want when we want and leave the wives and kids at home. In the town of Gilbert it is totally legal to ride on the roads with your ATVs. Police just request that you follow the rules as if you where driving a automobile. I have my Banshee and Bill (Neighbor) owns a Yamaha Raptor700. Both of our bikes on occasion where being scoped out last year to the point where the police knocked on our door one night to let us know this. Both of our bikes have lots of Bling Bling. Well this year my Banshee is going to even look better. I just got my shipment last Friday of my New Hiper Tech3 Dual Bead lock wheels along with New Maxxis Razr2 tires. Heck all it takes is 16 lug nuts and Wheels are gone. The upside is the motel we stayed in last year We where able to park and lock our bikes within 15 feet of our door (ground level). I'm worried about this. I'm thinking locking locknut on each wheel. of course we will in addition lock the bikes with our very thick cable and very Beefy locks. Any ideas in addition to what I have said I highly welcome. Thanks Guy's!!!!!!!!!!

Hey Guys, Does anyone know if anybody makes or sells a set of Locking Lug Nuts for our Banshees ? Similiar to a Automobile where you have one locking lug per wheel/Rim where you need the key to get the lugnut off.

Hey Evan, How many ounces was the tube and what did it cost ? Thanks.

Go here and Under "Product Description" is a good Description of what product does. http://www.amazon.com/Eclectic-Products-380012-Seal-Adhesive/dp/B0000AXYZG/ref=sr_1_1?ie=UTF8&qid=1330809369&sr=8-1