fastrthnu

150 plus shipping, no bends, breaks, non factory welds, stripped holes or title.

yea any screw in comp tester will suffice from an auto parts store, northern, harbor, ect. they arent all spot on, blut close enough. if you want a good one, order from snap on, mac, matco, ect remember if you have to use a threaded adaptor, see how many ccs it takes up cos that will throw you off quite a bit. I think its about 12psi avg per cc. so say if yout adaper had a volume of 2ccs on its own add 24psi to your gauge reading. 12 ISNT spot on, but an average.

I will def have to make the next one. Howd ya do Saturday?

your first sentance was retarded, 2nd 3rd, and 4th already said, and 5th didnt make any sense.

I think I may. Im asking cheap for the bottom and got a few interests and no takers, so I might as well make more and part it as well. The quad is comming completely apart tomorrow for new pics and shipping already bought parts, Im going to look into some fair prices on a parted bottom end, and Ill post what I come up with. Thanks.

wow 10cc is a small dome.

my next motor will prob be a cheetah pv. I know the t-rex is a good cyl, but I hear for some reason the are really tempermental as far as dialing in/tuning. I dont know all that much about em tho.

take it apart? blown as in just worn out? or blown? you can see the pistons through the exaust port if itll help. then you can see the cyl wall and one side if each piston. normally in comp is gone its hard to start cold/warm, and kicks really easy with little resistance. if you own a banshee, just get a comp tester. just take the exp. chambers off and take a good look

well, here it is saturday morning, Im supposed to pick up my late payment this morning, but no answer whe I called, my batter is completely dead and doesnt want to hold a charge, and I cant figure out how to get this black thing next to the coolant backflow tank back on. Im getting pissed. Plus I still have to stp in port charlotte to get my riding gear. Ive got 11 dollars to my name until I get that check.

reeds are sold

Pipes are sold!

--UPDATE-- nerfs and flywheels sold pending payment shocks, a arms, tie rods, brake lines, and axle are sold.

NM, they are sold,.....

to early for what?

I cant upload it, but I have one already on my phone, pm me your number.

if you put a turd on a golden platter,.. its still a fucking turd. wtf ,.. its a fucking scooter!!

yea I think thats the best route to go. they race quite a bit near here at immokolee 1/8 mile. always seems on the banshee ya just wanna wot bang through gears and just go fast lol.

I have 2" spacers on my yfz until I get money for a long travel and they suffice. I didnt buy them tho, so there is that as well. bump steer doesnt bother me a bit but then again I can bench press what my whole quad weighs

cleared it up bro, sorry bout that!

ive seen rears like that, but not fronts.

for sale, Im getting tired of this on my garage floor to the point I might put it back on, but that requires work. $180 shipped retail new for 550-700 bucks. this is full system, head to silencers. loud!!! have better picture off quad I can send by text. be like bwwahhhhh bwah bwah bwahhhhhhhhhhh

yea, the yfz isnt nearly as powerfull, Im always tryin to find 6th on it, but it handles great, im really comfortable on it, better on gas, ect ect Ill always have a banshee one way or another but I think Imma build a 10mm + for the straightline.

parting out my whole banshee,.. for real. I never ride it, and I want a bike. so here we go. --98 frame yellow ppg hd paint $150+shp --g force axle +4 $85+shp --rear hubs yellow $20+shp --rear carrier yellow $20+shp good bearings Ill inc srocket hub w match paint --rear wheels blk hipers/mx6 $350+shp 80-85% tread --34mm mikuni tm flatslides $150+shp --front wheels douglas flipped $65+shp --+3+1 a arms w lines n ties $375+shp --elka piggy rez shocks $500+shp --rear brakes (complete) $50+shp --ac pro peg nerfs $50+shp --rocket pipes $300 +shp --pods for carbs $25+shp -- negative 2" swingarm blk $150+shp --boyeseen dual stage carbon fiber reeds on stock cages $35 + shp --renthal bars $10 +shp -- nacs billet bar clamp $10+ shp -- asv clutch lever $ 45+ shp -- front brake master cyl/lever $15+ shp --front rotors, brakes $55+shp w a arms $30. -- Passion 12 port RZ cylinders (for 4mm) they are 65.5 bore, new pistons. they bore is new. they have about 20 minutes run in on them. the dick that did the bore didnt clearance the pv`s and the piston and rings rubbed it. they need new rings and hone. pistons are still good. the worst cylinder holds 160psi. the stroke clearanced and milled head comes with. (cyls, pistons, head) very rare and expensive combo $600+shp run with vp110/93 @ 50/50 --Full Banshee setup RZ harness with matching rz 200w stator, servo all the jazz $150+shp --lightened flywheel $65+shp --4mm bottom end excluding above but with side covers, kick, shift, 4mm crank, billet basket, hd springs n plates $500+shp Or motor whole w harness for $1200. Misc brackets n crap, ask or throw offers. tank radiator plastic ect dont sell for much and will prob sell really cheap or go in trash. Anything left over by Sat 15th will be listed on eGay. Postal Money orders get 10% off. I have paypal. Please pm me for contact information or any questions or both. I will sell the bike whole as is for $3500 or trade for bike year 01+ and 750cc + gsxr, r1, 929. (mirror effect on picture) (because this is hot)

supercross/mx and wide open fast trail/gncc type. we sometime have roundy races out here, but this time of year the woods are all full of water. Thet have flattrack races here in Naples alot, but Ive always to some reason I can bring her out. Since Ive gotten my 450, Ive hardly paid any attention to it. It stands 52" wide up frnt and 50" in the rear, so tight trails are a no go, but I dont care so slow winding, I like to be in 4-6th in the woods. I have tried to bicycle this thing on asphalt and cant get the tires up an inch, it suck up my weight or slides around. very stable through high speed turns. If you see the picture of the purple/yellow banshee on the upper heading of the site w down right dirty is an older less modified picture running at the seminole supercross track. I can bring her up I guess. She is shy for about 5 minutes, then she wont want to go home.

my daughter is 10. they are rocket pipes. they arent made anymore. I havent held my leg on em long enough to burn em, but I have toughed with shorts on and burned my bare leg. these are the propeg nerfs. they are good, but they dont have the heel guard on the back like my 450 does. I dont know if they are lowered, but they have hit the ground a few times riding. the elkas made a night and day difference in the riding. I can ride hard trails all day and not get arm pump, and jumps/whoops are more like clouds. I have then set pretty soft, the bike squats about 3" when I get on and it bottoms out on air 4` and up, but other than that, it rides very smooth for a banshee.