375hp banshees

never enough :yelrotflmao: :yelrotflmao:

lean is mean, but that doesn't mean its right or will last... i would do A plug chop,do A low speed check, & put your coolant of choice (not st. water) when mine gets that hot, I air it out or, if there isn't room, just shut it down for a few min's & good to go

its normal... no air, no cool... the gauge is the 1st thing i put on my shee, its A must If you ride slow or do alot of ...most people don't realize how hot they get w/o air flow ..then again most people ride at A good speed & don't have to worry about it, but i like to see it i've seen 230* & no boiling over so w/ A gauge you know! simple ,cheep, ins IMO

there ya go :thumbsup:

& if your not A member here is A pic :biggrin:

hard to say, i'm up to 360 at sea level unported, other mods in sig., but thats rare (hi) ... I wish I knew what makes all the differences but i've heard a large range w/ same mods, you should be close w/ 330,340 try it & do A plug chop

hope your running race fuel w/ .25 shaved off :yelrotflmao: should be close to start might be a little lean try it & do a plug chop

yeah, i'll give ya 2 cold ones & you can keep the mine for the caliper shipped LOL

& when you leave there swing by my place & i'll give you the bolts I could use it too but long drive good deal for somebody, free parts, meet A fellow bhq'r & drink A beer :beer: might wanta specify the beer quality, to help enhance the deal!

hurt mine alot, when I got back arount to repairing it, it was gone!! stolen right outa my shop (my old shee) :verymad:

your filters clean ? (sorry had to ask).. what do your plugs look like...as it breaking up or just rev's slow

just bought some heavy duty stripper from the same company stripped my jugs in less than 5 min good products!!

I bought A chrome, 1 gauge holder & put in the top middle screw to the rad. cover... just used 1 screw hole & made a gasket to keep it from scratching my cover & bent the holder closer to A 45* than 90* to see it better I think it looks good? if you got one w/ a light or Any holes seal them dust gets inside & sticks to the inside of the glass ::

so is what dawarriorman said correct, that explination made more sense to me but, maybe i'm one of those stupid people :shrug:

wow you need to change your sig! and Travis that has to be the worst & best pictures ever (still like the chrome one better)

so firehead, by making your spring shorter or longer installed, doesn't make any difference except for the ability to travel more before binding(because you make it sag to much as soon as you sit on it)...A 200lb rider w/ spring as tall as you can adjust it, will sag the spring at the same rate as A 200lb rider w/ the spring adjusted as short as it can be assuming it doesn't coil bind (bottom out) except ride hight or center of gravity (if that is the correct term) not being A smart, ass realy want to know Dave

OMG, I couldn't begin to imagine that

only if you want to be :biggrin: banshee, sound like a perfict fit, don't ride one if you don't think you want one, once you do, you'll buy it :thumbsup: make sure you school yourself on 2 strokes too ...oh & most important, find the BHQ alot a help there, & welcome to the addiction :yelrotflmao:

LOL :yelrotflmao:

get w/ jankab, he just did mine haven't put it to the test yet, but very nice work :thumbsup:

how's he doing tit? my daughter loves to ride, I bought 3 quads 3 yrs ago & my wife rode once (not realy her fault, alergies)

every bike is different, do A plug chop.

glad to hear i'm not alone , DAMN BANSHEE'S

lol, I take up the rear, paddles aren't to follower friendly

I don't think it helps but maybe 5*, not worth the $ in imo for cooling purposes