zilladude

My Banshee has only been down once this year, too bad it has been the whole year so far. Damn winter rebuilds The Zilla has been good for 2years now.

If you have a stock stator plate there are no adjustments. You just have to tighten the bolts. The torque on the flywheel ins 59 ft/pds. Wieseco rings can be installed any way on the SHEE's I usually install them with the size # facing upward.

What condition is the clutch cover in? price too

28mm PWK's taper bored to 30mm. Wide open power of a bigger carb & the response of a smaller carb.

I live in Minnesota, 20 miles south of St Paul. The only things that I was going to do was replace the front shocks. ( they still work but are the originals) & when it needed to be freshened up I was going to have it ported. I wanted to see what it was like with just a pipe & carb when I built it.

R50 in the SHEE & Castor 927 in the ZILLA. Both mixed with 110 smells sweet.

I have a complete Pro Design pro flow filter. dual stage foam with the aluminum airbox adapter. 50.00 shipped

I need your e- mail address so I can send you pics. I need to get 3200 for it. I have way more than that into it.( over 2000 in the motor alone)

1987 Quadzilla, needs nothing but a rider. I sent you a pm

My rear rims that I had listed mysteriously(sp) dissappeared from where they were being stored. I think that they must have grew feet & walked away.

The 03 LE is black

I will get a pic for you tomorrow, my battery died in my camera

No need for another axle. Sorry

85 in a K-car!! Those things couldn't do 85 even when they were getting towed to the bone yard.

I have a Pro Design foam filter set up with the aluminum mount in excellent condition - 50.00 shipped Black aluminum bars, Wirtz brand Banshee bend. new, never used - 35.00 shipped Stock grab bar, some scratches not bent- 20.00 shipped Stock gas tank/cap, all bolt holes are good, threads perfect-25.00 shipped I can get pictures of all of these parts, pm me your e-mail & I will send them. I am open to reasonable offers

I was just going to ask that. Got any pic's?

14mm 1.5thread pitch 3/4" long 13/16" or 21mm wrench works perfectly for removing the plugs

I think it is the replacement for the series 2000.

I need to sell, Open to serious offers also. Possible trades. I have some extra parts for it.

I have over $5000 invested in this over the last 3 years. The engine has about 10 hours on it. 15 hours on complete rebuild of the quad. the engine is new, including all fasteners. New cases, crank, cool head, cylinder, 41mm pwk carb, 130w stator, lightened flywheel, clutch & basket, water pump assembly, all bearings & seals, shift shaft/ pawls/ retainers, reed cage, pro series reeds, & intake boot. The frame is painted red & it has black maier shiny plastic. Also has a PRM bumper & rear skid plate, AC glide plate, trail tech torch lights, & a Paul Turner pipe w/ fmf silencer(spark arrester). I would like to get $3500 for it. It has always had Maxima castor 927 mixed at 32-1 in 110 racing fuel. I can get pics if interested.

Check the spark plug caps.

NTWonline.com Get the TRXUS radials, they should last longer than the bias ply ones. radials are 305.00 (38x15.50r-16) bias are 227.00(39.5x15-16)

The group is StoneSour, the song is Bother. sweet tune

new 03 LE frames are around 550 through Ronnies.com

We are either taking my friends 03 red Silverado HD or his Dodge van. As for quads- LT500, 2 LT250's w/ 500 motors in them, an ATC250r, 400ex, & a polaris 400. I wish I could bring the Banshee, but I didn't have time to finish it. there maybe more coming with but they haven't confirmed it yet. Dan