tats4life

I went riding this weekend near my parents house in georgia. There is a guy that sent his entire motor to baldwin motorsports and was completely gone through. We dragged a couple of times. He beat me out the hole everytime, i was spinning to hard, but i'd click into 3rd gear, look at'em and just wave bye, bye, didn't even need 6th gear. We jump onto the track and he couldn't keep up, but his suspension was bone stock by appearance, he could've had his shocks redone, don't now.

Can anybody with a digital camera take a picture of a stock spindle layin around. More specific of the mounting holes for the ball joints. My buddy got a basket case shee. The a arms he got don't have ball joints and we're trying to find ones that fit. I think the spindles might be reamed I'm not sure, never really messed with lonestar stuff. My leager ball joints don't fit the holes. The ball joint goes in and seats tight but there isn't enough threads on the ball joint to tighten it down on the spindle, and i don't feel like tearing apart my front end. Or can somebody tell me how big the hole is supposed to be? Thanks

Scott, The only no link set up that works for mx on shee is a leager frame and no link swingarm. Its the cr500 setup. The frame and swingarm is right aroung $3300. I've riden that set up and it doesn't make that much of a difference. How much travel are you trying to get.

I'm with evil on this one, heavier the better, ain't nothin wrong with breaking stuff . When the moods right, i'll take some Cypress Hill.

You sound like me, if you don't have bad luck you would have no luck. You and your family are in my families prayers. I wish you the best of luck, I wish I could help out but I'm on the freakin east coast. Best of luck.

All out horsepower definitley a banshee, but a tight mx track, the old ladies 440ex. I prefer a 2 stroke. Espically the ones when it hits the pipes it feels like its trying to rip your arms out

My front end is roll design, which is +3+1 gull wing design. My front end from outer edge of wheel to outer edge is 52 1/4 inches. I have to run 19in front shocks. If the a arms are not gull wing design, there's no point in getting that wide because you can't run a 19in front shock the ball joints will just bind up on the spindle. You want to make your front end as wide as your axle. I run a dominator +4. My shizzle handles damn good

I got chrome +2+1 denton arms for 400 obo, I am selling a set of alba pro-comp black +2+1 arms with about 20 hours of riding on them, $525. Buddy went all out drag, couldn't handle mx. PM or email

It doesn't matter where dealers don't get that much of a break on prices. I'd just look around, baldwind motorsports, poloypro, check your stealership my local guys carry. The shipping is costly since the front is one piece.

I round pc's and ptr mids. The mids are on a national motor kit, and I out pull just about every banshee on the pro-am nat circuit. But I have had my ass wore out on a tt track against cpi's and other pipes. The ptr's work great if duncan builds the motor. I have the pc's on my drag shee, they work real good top end. I also run high rev ptr's, the work awesome all the way through the power band. My drag shee is ported to the moon. I have ridden many banshee's with pro circuits with a mild mx port, for the money you can't beat'em. That's my worthless 2 cents.

Happy birthday bro, 3 things, go ride, get another tattoo, get really red eyed!!!!

do you want to hide it or make it noticable?? minds hide and my buddies is underneath the front end of his shee....

just turned wrenches on the shee's, and got some cold sweats from time to time, but still was able to chat with some hq members.

Yes my wives loves my shee's she just hates that she can't hold on. But shizzel can ride the shizzel out her 440ex. Last time we went to macon she was handing my ass to me in the corners. She's not scared to stick a wheel in on somebody. I turn into a puss when i ride with her, cause if i beat her ass around on the track, i'll never her the end of it or never get any again. The photos everyone speaks of she won't let me post them.

Scott, Sorry I didn't make the race this past weekend. I was on the other side of charolette (sp) when pops called and said he was following the ambulance with mom in it. Then dad told me what happened. My mom had a mild stroke friday afternoon about 2:30. Needless to say i didn't give a shizzel about the trailer when i turned around and headed to augusta,ga. Got to the hospital she could only have one vistor stay the night, i made my dad stay. I went to the drag strip to blow off some steam and try to relax. Made one good pass, did my burnout staged up, let the clutch fly and my fuckin sprocket hub broke, my night ended. Coming home sunday night i got a fucking speeding ticket from a rookie cob, is said i was going 48 in a 35 zone, yet i was only about 25 yards off a stop light, pulling a 36 haulmark with an f350 dually, what the f*ck . Hope everything went well for you in the race. Sorry to everybody else that reads this i just had to vent alittle.

My pratice track takes up 15 acres. My buddy came out on an enduro bike a few weeks back. One lap on is bike was equal to 3.5 miles. I have box vans buried, an old boat, my whoop section is 18 55 gallon drums buried 1/4 down. Behind my house is the nut checker...... First jump is a 55 ft table top, but then 35 ft later is a big double, you can leave the face of the table top and land on the back side of the double. We measured it at about 93 ft give or take. Hell my wife scared the shit out of me when she cleared the whole damn thing last weekend. I'm going to try and buy a digital camera and post some pics. I'm still in the past with a 35mm :oops:

I have a sponorship through duncan, the mx port is killer. Guys i ride with a various mx port thorugh other shops, and everybody says my hits harder than everybody elses on the track. Has far has drag port or a bottom end port goes, I can't give my opinion I don't have it. My buddy port the hell out of my drag shee. The only draw back about duncan is you have to run his pipes to get the most out of his port work. His pipes now are $735 chromed w/silencers . Hope this helped.....

Scott, Where's the last race sat. I can get off work early friday and drive up with the haulmark. Just pm the info. Do they run the 4 stroke and 2 stroke together or seperate. I'll bring the wives 440ex if they split. Sorry guys the better half can't hold on to a two stroke :oops:

I race mx and drag and both my banshees have the did x-ring chains. I have never had a single problem, but other guys I mx with run that damn 150 sidewinder chain, it's badass but costs to damn much.

I don't know how old your are, but damn who ever taught you how to spell you need to go get your daddy and have'em beat there ass, you DUMB fucker, see it has a the letter m in it. Your shit must be pretty ragged out to only want $4000 for it. My mx shee is a 00 and I won't sell it for less than $10,500. And the only thing left stock is the cases. Anytime you wanna get your ass handed to ya, just let me know. I got some family in Ft Myers. I'd be happy to come see them and hand your punk ass to ya FUCKER :twisted: Or your daddy might not let ya play with the big boys.........

Thats funny but on the other hand that's fuckin stupid, if your going ride something that can seriously mess u up or kill ya, why the hell would you do that???

i bet you got one phucked up grill, just thinking about using my teeth makes them hurt :oops:

The fox air frames make a pretty damn good bottle opener. Just like blue duece says, it's handy when your stone sober facing a man killer/maker. Get'cha a couple down get the head ride and pull your balls outta ya throat and nail it. GO BIG OR GO THE FUCK HOME :twisted:

Which one? he has two motors done by them, and one cheetah motor by trinity that I had the pleasure of handing it's ass to it. Duece comes back to Columbia once a month and runs his mouth and basically gets his ass handed to him. :twisted: Duece thinks he can scare people from racing when he waves wades of cash, Taylor performance has raced him more times and took more money from him than anyone. But Duece never drives the bikes, his cousin who races busa always drives.

Nyuk, can i have it i'll be your new best friend, and i'll let you ride it enough with the bullshit, when you get it bolted on, are you still going to run meth. What kind of hp numbers are you looking for. I don't have shit that can touch that, unless I get another credit card. And duece's busa raptor SLOWWWW, taylor performace handed his ass to him for $10,000 in NC.