smokin 2 stroke Posted February 15, 2007 Report Posted February 15, 2007 (edited) how should i clean it. their alot of dirt inside of it. its for a blaster by the way Edited February 15, 2007 by smokin 2 stroke Quote
theshee Posted February 15, 2007 Report Posted February 15, 2007 You have the cases split? If you have the cases split just use brake clean, just dont breathe that shit, about killed me a couple times. Quote
banshee9o9 Posted February 15, 2007 Report Posted February 15, 2007 how should i clean it. their alot of dirt inside of it. its for a blaster by the way I'd say maybe carb cleaner or Brake cleaner it evaporates pretty quick... but you have all the guts out of it take a pressure washer to it but thats only if you have all bearings and any other internals out Quote
locogato11283 Posted February 15, 2007 Report Posted February 15, 2007 if the cases are split just use some parts cleaner. if they are not split use a garden hose or pressure washer and get all the nasty shit out. then run some parts cleaner in there... Quote
smokin 2 stroke Posted February 15, 2007 Author Report Posted February 15, 2007 their slip open but their alot of bearing still in the case itselft. i dont need to remove these for what im doing. so i can just use brake cleaner Quote
Animalman294 Posted February 15, 2007 Report Posted February 15, 2007 That should work.................. :thumbsup: Quote
IROOST1 Posted February 15, 2007 Report Posted February 15, 2007 i wouldnt use brake cleen. it will eat at the cases. use carb cleaner instead, its made for ferous metals. or best is take it to the car wash and pressure wash it. then once it dries out, spray it down with wd40. Quote
theshee Posted February 15, 2007 Report Posted February 15, 2007 dont want to start a beef, but brake cleen wont hurt the cases.. if it would hurt them mine would be fully disolved by now. That shit will hurt you alot more then the cases. Quote
thegroup Posted February 15, 2007 Report Posted February 15, 2007 dont want to start a beef, but brake cleen wont hurt the cases.. if it would hurt them mine would be fully disolved by now. That shit will hurt you alot more then the cases. kindof what i was thinking, isnt brake cleaner and carb cleaner basically the same thing, just ina different can? Quote
375hp banshees Posted February 15, 2007 Report Posted February 15, 2007 starting fluid, cheeper & evaporates w/ no film at all (so oil it up right after) Just get the cheep stuff w/o upper cyl. lube Edit: if you get it in your eyes just open them it will evaporate very quickly... get brake fluid in there & you'll never use it again :yelrotflmao: Quote
smokin 2 stroke Posted February 15, 2007 Author Report Posted February 15, 2007 ok cool i will pick some cleaner up tomorrow Quote
FireHead Posted February 15, 2007 Report Posted February 15, 2007 Some of us use diesel fuel to clean parts as well. All of the other brake and carb cleaners suggested above work well too. :thumbsup: Quote
dajogejr Posted February 15, 2007 Report Posted February 15, 2007 kindof what i was thinking, isnt brake cleaner and carb cleaner basically the same thing, just ina different can? No... Carb cleaner I've used leaves a little bit of an oily film behind, whereas brake cleaner dries quickly and clean. I agree...I've always used brake cleaner with great results....shit will burn your hands with too much exposure, though... Powerwash then brake clean it...then power wash again!! Quote
smokin 2 stroke Posted February 16, 2007 Author Report Posted February 16, 2007 so power washing it wont hurt the bearing that sit in their now Quote
IROOST1 Posted February 16, 2007 Report Posted February 16, 2007 i think brake cleen is a different chemical than carb cleaner. carb cleaner definetely isnt as strong. also, some brake cleaners have chlorine in it. so im sure that would affect the cases if it was left on. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.