BSHEE400
-
Posts
335 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Store
Everything posted by BSHEE400
-
i've tried quite a few different goggles, but for me there is no better or more comfortable fit than the oakley crowbar mx
-
welcome to the addiction when your gonna start modding you should check out the site sponsors, they've got some great deals and customer service.
-
correct me if i'm wrong but wouldn't that make power more like a 4 stroke?
-
Anyine know the web-site for Cool Blue Coolant?
BSHEE400 replied to jon321's topic in General Banshee Discussion
why not just add a cup full of water -
looks flawless, nice work
-
is the piston in the caliper releasing the pressure fully? if it's keeping even a small amount of pressure on the pads they wont last. can you turn the axle easily by hand with the rear end lifted? stock style or roundhouse swinger?
-
i'd reuse it also, sounds like the clip on the master link wasn't installed properly
-
i ran it for a while and it seemed as good as any of the others that i've tried, i stopped using it because i just didn't like the smell
-
sweet bike i love the stealth look
-
link won't work for me
-
what type of clutches should i use!?
BSHEE400 replied to rangerjay's topic in Banshee Repairs and Mods
i too was running the barnett carbon fiber clutch which seemed great until i switched to the cub, then within a couple of rides it started to slip like a mofo, and by no means was that a cheap setup do it right, do it once, put the fast clutch in there and be done with it -
i can't remember for sure but when i got the trinity 2 -1 setup i think it came with a terrycable cable. and when i switched back to dual 35's it is a terrycable one i'm now using so i'm sure they'd have the right one for you also
-
good luck with the build
-
+1
-
what type of clutches should i use!?
BSHEE400 replied to rangerjay's topic in Banshee Repairs and Mods
i too would recommend the fast clutch, been running it on my cub without a lockup for about a year now and it has been flawless -
i've been running the same set of vforce3 reeds with a couple of years and have never broken a petal, everytime i clean the carbs i check for gaps also and they are still good. how many petals have you broken?
-
i'm gonna say yes but i guess you'll just have to test it and decide for yourself
-
i've been rocking douglas red labels with a few years now and they are really tough, i ride a lot of rocky terrain that used to bend the shit out of my stock ones but these red labels just suck it up lol
-
glad to hear you got it sorted it's a bonding experience lol
-
i've been running the ek x ring chain from jeff on my cub with a year and a half in all sorts of conditions and it has been flawless, still looks like new also
-
flip the frame put a nut on the end of the stem and use a heavy rubber mallet on it, you should probably replace the bearing and seals while you have it out. as for the frame the upper hoop looks good so i think the part of the frame that holds the bearing has some how been bent upwards, that's assuming your stem is straight
-
i'm guessing krylon fusion seeing as it says it in the post above you lol
-
i run renthal fatbars that are for an mx bike, but i've got a +2 antivibe stem so they're perfect for me standing at 5' 9" i also really like the width
-
Any tips on securing a Banshee in a garage to keep it safe?
BSHEE400 replied to jon321's topic in General Banshee Discussion
my banshee is kept in a big shed with a lot of expensive equipment, dirt bikes and what not. the door is never locked but it has three bad ass doberman to keep it compeny -
once you get used to them they're fine, i like the idea of my ankles being safe as one of them is already weak