375hp banshees
-
Posts
6,699 -
Joined
-
Last visited
-
Days Won
195
Content Type
Profiles
Forums
Events
Gallery
Store
Posts posted by 375hp banshees
-
-
I think its a guide not really a jet
Sent from my SM-A505U using Tapatalk -
iirc, you can see 34, through the air horn, did you see note about SDGAA?
Sent from my SM-A505U using Tapatalk -
Check list
https://www.sudco.com/genuine_vs_fake_carburetors.html
Sent from my SM-A505U using Tapatalk -
1 hour ago, jst854 said:
The over flow is not overflowing, which makes my theory make less sense but it's the best one I got now.
Sent from my ONEPLUS A6003 using Tapatalk
See if its plugged if so it will make a small prob. worse
-
Is your over flow flowing? Maybe try & set hight, to seat off flow sooner in that carb, for now & see?...i assume youre only having issues with 1 cyl. & you swapped carbs?
-
If it were old carb's or knock off's i'd say dig deeper but, prob. Not the issue.
Typically the fuel inlet needles, "seat" o.d. is fitted into the carb body, via an oring. which gets over looked during an old carb rebuild & the needle seats on the i.d. of that.
-
The fuel will put up pressure on the needle (via float), to keep it seated....kinda hard to duplicate that
-
44 minutes ago, proven said:
Where can one post photos? Like 2022 size ones 😂. I’m Will to donate to memory space.
Tapatalk
-
2 hours ago, proven said:
Second attempt at getting these my shee been down for a month now. On top of that, the domes weren’t stamped so I did a quick syringe test they looked deeper then my 22cc’s, I ordered 21s. They held at least 24cc of 151 proof alcohol. SMH I should have just ordered from noss and spent a few extra. But has anyone else had notched and scratch’s on theirs? Is it normal?
I'm reporting you for alcohol abuse
...spill da beans, who'd you buy them from?
-
2 hours ago, jst854 said:
Fairly confident it has to do with the needles properly closing off the fuel supply. I turn the gas off and it runs perfect until the bowls go dry. Just had the floats set at 19mm will verify tomorrow that the needles are holding pressure when closed and go from there
Sent from my ONEPLUS A6003 using Tapatalk
What do you have for fuel tank vent?
-
15 hours ago, jst854 said:
Stock jugs Eric Gorr woods port. I haven't reached out to him regarding jetting as it was running well, thought I had it pretty close until whatever this is happened
Sent from my ONEPLUS A6003 using Tapatalk
I'd start there & see how far off you are if@ all
-
What cylinders are they ...who ported them... what did they suggest for jets?
-
Cylinders?
Sent from my SM-A505U using Tapatalk -
Is it running out of over flow?Threw the stock reeds in, no change. Maybe I am adjusting the float wrong, seems like it is being loaded up with gas. I will try that again tomorrow
Sent from my ONEPLUS A6003 using Tapatalk
Sent from my SM-A505U using Tapatalk
-
K. Those look legit
...ya'll m-fuq'rs'll reply to biden& rona thread...
help a hq'r out ferachangewhydontyouinz!?!
Sent from my SM-A505U using Tapatalk -
Are they Square or octagon?
-
Kinda looks like knock off?
Not saying thats the the prob. But fyi
-
Hard to see... how is the corner shaped
Sent from my SM-A505U using Tapatalk -
Looks like you have air box on? try pm'ng ayesully he's pretty good at jetting ...hasn't been on in a while tho...maybe a he' ll get a pm tho?
Sent from my SM-A505U using Tapatalk -
Are the corners of the reed cages at a single 90° "L"
...or are they "\_/"
Sent from my SM-A505U using Tapatalk -
Filters aren't over oiled?
& see above edit reeds
Sent from my SM-A505U using Tapatalk -
Youre sure theyre not knock offs? or reeds Corners 90° or cutoff?? Still have OG's
Cylinders?... ported?
Sent from my SM-A505U using Tapatalk -
^ knows nIcK technology
-
I doubt that'll help
New Engine ran well and now is un-driveable
in Banshee Repairs and Mods
Posted
Put og jets back in & hopefully the og problem was fixed, with the 1st cleaning.
Sent from my SM-A505U using Tapatalk