Jump to content

375hp banshees

HQ Premium Member
 View Profile  See their activity

  • Posts

    6,882

  • Joined

  • Last visited

  • Days Won

    209

 Content Type 

Everything posted by 375hp banshees

  1. 375hp banshees
    Manual is correct
  2. 375hp banshees
    Might want to hit up camatv iirc the hinson had issues ( think it can be addressed iirc?)
  3. 375hp banshees
    ^ likes smelling seats^
  4. 375hp banshees
    Use tapatalk Sent from my XT1080 using Tapatalk
  5. 375hp banshees
    That will be hard ,since you don't know what you have ( to many unknowns) Sent from my XT1080 using Tapatalk
  6. 375hp banshees
    First thing is compression and elevation
  7. 375hp banshees
    You can't compare a 70-90 HP to a bolt on stock bore banshee, no matter what the compression is. As far as current compression the fact that it has new pistons in a stock bore & 19 domes seems odd to me, could be squish due to dome or gasket mismatch? But i would lean towards side clearance Sent from my XT1080 using Tapatalk
  8. 375hp banshees
    If wall clearance looks good & it runs OK send it , unless you just want more . which I assume you do , or you wouldn't have wanted to change dome sizes
  9. 375hp banshees
    When you adj. Idol with screw, does it change rpm?, a lot adj. Idol with cable so screw. might be backed off so it's not hindering cable idol adj.?... Edit: Timing I'd check comp. And compare to elevation. most don't run more than 5 ( stock)
  10. 375hp banshees
    He's alive...What up Jeff!
  11. 375hp banshees
    Don't run 17 @ sea level! Don't know if i'd only run 95@ 175 either. squish is on the tight side Whatever you do , DONOT ask your Builder
  12. 375hp banshees
    I guess Polaris has tors too. ETC = tors Canadian speak ...probably common knowledge to Polaris guys. figured I'd share any way... 1/2 broken wrist , broken key & stuck bendix later but... Found it
  13. 375hp banshees
    ^^ I'd ck sync 1st tho. Sent from my XT1080 using Tapatalk
  14. 375hp banshees
    Does it have to be a good bitch macanic? Or will a good bitch do?
  15. 375hp banshees
    No, does it only sound bad at or just above an idol Sent from my XT1080 using Tapatalk
  16. 375hp banshees
    Is it only @ idol- just off idol, what does it sound like with choke out?
  17. 375hp banshees
    Yeah i'm lapping it this time , just didn't know if the locktite would effect the bite ... He's not buying a new flywheel, already told me that so, we'll see
  18. 375hp banshees
    Not if it was in good shape but it's not it's not on a banshee and hopefully i'll only need to pull it off if it spins again and it'll be loose at that point. Put red on it w/o lapping it or knowing it' history & it spun again...4 poke backfire
  19. 375hp banshees
    Threads are fine, just taper areas. Didn't know if 64040 would help or hurt on taper
  20. 375hp banshees
    When you lap a questionable crank/flywheel, do you use Loctite afterwards for insurance, or doesn't help ?
  21. 375hp banshees
    Si' Sent from my XT1080 using Tapatalk
  22. 375hp banshees
    Now back to your regularly scheduled thread already in progress... So, is it as cast or did your builder send those gaskets with it after port job?
  23. 375hp banshees
    ^This Line up tops, not bottoms 110 vs 115 rod? 121 is stock iirc
  24. 375hp banshees
    I'd assume the old top end was different set up than current & he did a shotty job re assembling current... Now you have to decide how to go back together with it . but you'll have to find out what the 2 are , what's on the rods for #'s
  25. 375hp banshees
    Do you have a way to measure the old cylinders & compare it to current cylinders . assuming the spare cylinders you said you had, are from the old pistons you are using in comparison... Did he give you an old crank?

BHQ Quick Links

×
×
  • Create New...