camatv

mp

pico's

mo pics

oem plastic NOT maier, paint a few years old in good condition not mint some damage to rear from chain flying off. smal dent and paint chip.. clearcoated and used flex in them they will not chip from flexing AT ALL> can be waxed and polished. complete plastics WITH SEAT pan is lightened ( holes drilled in pan + foam.) very soft seat 425 with out grill 475 w grill OBO!!!!!

i am going to try and sell my white and blue painted drag plastic to buy these...!@!@

will come with rear brake assembly but not the axle if you want the axle i'll sell it seperate.

mo

hyme joint steering conversion, reinforced steering stop..

had a 420 cub in it was a blast to ride i went to a 480 pv sheeta and its just too much for the lil swing arm i am putting the motor in my lsr frame.... ONLY reason i am selling is i dont have the room a TON of time in the frame...

here are some pics. wont come with front wheels tires, will have stock front hubs not the lightened ones. no axle or rear wheels axle is for sale tho.. RIS designs drag axle. no carrier, will have gas tank with pingle if you want shorty drag handy bars i got those instead, have a e~z adjust clutch perch that will go with it. and maybe a billet throttle.. i may part it out a lil later if i get enough interest this frame is very very straight the front plastic lines up excelent the top bar has never been pushed in its never been flipped. the tank pops right out the subframe is not tweaked or bent either. will have black plastic on it rear plastic is full fenderd. stock black front will be painted.

i am thinking of selling my ole 87 stock frame that i lightened down it has a 480 pv motor and its just to hard to ride the way i want it to its had a 350 gas drag motor in it. a 420 cub drag motor and this 480. its been lightened and powdercoated red/ clear there is a small amount of flake in it but not much, i am putting the motor in my old lsr drag frame. it has denton j-arms on it they are stock width but +2 forward one ride on new ball joints. will come with steering stem , foot pegs, shifter, brake pedal, motor mounts all rainbow powder, j-arms, swingarm tucker pro am + 6.5 round house, plastic stock, grill, gas tank radiator, hoses, rear brakes with new pads, stainless line billet cover on rear brake and street bike resivour with no rear mount, billet rear grab bar, asking $1500. this frame is light and works great. i will get it apart and post pics.. a lot of work went into this frame set up its been great and ran great.

back side inside of the pipes yo can see on the bottoms there is some rusty discoloratin. its should be able to just be worked off with oven cleaner and a scotch brite pad.. silencers are great.

pico 3

pico 2

pics. its just on the inside of the pipes there is some what looks like surface rust i havent really got crazy and tried to clean them up because when they are mounted and i clean the out side they look great silencers polish up nice. these pics are as they were pulled off the bike. its been sitting for a few months and they are dirty. i just dont like to try and sell junk like its new.. i try and acuratellly represent what i have..

just like it says shearer inframe drag pipes stamped 350cc- 440 ( i have these on a 480 pv motor and they are great) production chrome no big dents or really any small ones i will post pics up soon these are teh same pipes i was going to sell last year but decided to keep another year motor had so many problems they have had about 2 hours of run time since then. asking 375 for them..

what did it come off of?

yep long time ago its funny this cylinder will pound that cub into the ground. but i will pretty much have to just give it away.

400?

makes my vision a lil blurry to..

i am looking for a set of same side shearer silenced big bore small flange pipes.. and a set of 11 or 12 paddle hauler sls.

hey wes did you sell that shaw? and /od the tamers yet? if ya likee call me at 620 802 8807.. cameron

tt

t's n az

and it will come with radiator, plastics, tank, and a set of stock front hubs if you want. i also have an RIS designs drag axle and some smooth buffs for the front. IF you want all that..