Oilsmoke

Really Scroll down to bottom of page and you will see it.

I Used a pen magnet for rod & ball and Impact gun and held it with a gloved hand.

Man that is a Nice Ass! Ducman I just love Black & white. Oh and I agree with you too.

Thx Bigairee

Where can I get some? I am stripping my Shee down for winter mods and One boot has a Hole in it. So does anybody know if there are aftermarket boots I can buy? I would hate to have to seal it with silcone..

Yamaha builds them detuned so the public don't get hurt from the lack of skill. Than get the shit sued out of them. Picture a Well to do Family. Dad makes great Money but don't know Squat about Offroad Anything. Son (13 years old ) bugs the old man for one of the cool Fast banshees. Dad goes down to local dealership and has it delivery to the house, there it is Limited Model with Some T6 toomey Open air box Etc... All 60 RWHP Bad ass machine. The unskill son kick it over revs the shit out of it a few time and Nails the throttle pulling a Wheelie in National MX stlye Holeshot Right in front of the Old man, Tearing the Lawn into instant Mulch and Hiting the Rod Iron Fence Out of control And breaking his Shoulder and Right arm. Dad Was scared to Death seening all the Raw Horsepower almost Killing his Son and Call the lawyer after a Stiff shot and valium.So there is One major reason.Yamaha need to biuld for the masses. We the insane customize them to haulass.

What is the cost of engine ice vers water wetter for a banshee full? I drain and change offen. Just like tranny oil. So if. gunking up is a problem frequent changes should solve that.

Raxen If you get some Time

The side plates are .250 and Laid out on a Cad file then CNC'ed , Bars are .75 bored then tapped with Stainless steel 8mmx1.25x13mm. I Will polish them to Chrome like shine On my Buffen wheel Soon. Thx Guys.

I been looking into making one out of 1/2" chromoly tubing need about 10 feet at a cost of about 2.70 cents a foot. friend has a bender & tube notcher so i budget about 50 bucks to do it later this summer if I do it.

Here is one of my winter mods. I didn't like the lines of my shee without a bumper so I built this 20oz Alloy T-6061 bumper. Does anybody know the weight of a stock one? So here is my design. What do you think?

Spoin What did you use to gauge them?

It looks to me there Stock is with SLP only with no other mods. That is how I read it. What do you think?

I say write a email to Redline and ask a tech and then post there reply here.

Raxen I Am lovein all this Info Bro. It's some shit. I am cutin & pastin it in a File for Future use. I had my Son read it. Damm key board got sobber all over it now. Muhehehehe

So what's the part # for the fuel Pump and where to buy? and is 170 psi to much or should i get higher cc domes? I am 18cc at 4500 feet. And one more AS far a jetting when running Nos that is setup right for the nos. So would it be richer than normal jetting. I hope that makes sence.

Thx Raxen & superchicken. I had local say that you could lose a few topends before you get it right. I will start at a low level and work it up with rich jetting ? I am sure a true & welded crank is a must. as with Forged pistons too. what about High octane fuel? Timing etc? He has high compression too. 170 apox.

OK my friend came though Metal Price them out and let us know what you think?

Mr Raxen My son wants Nos. What is the better setup? Dry or wet? I never used it so I am looking for reading material. I found a wet system on ebay for banshee 435 dollars than then there is the boondocker for about 800 to 900 dollars.

Here are a few places metals online Metal Depot I used both , I like Metal online better. there is a cheaper place but i need my coworker to reply to a email than I'll post it. He as been biulding a sand rail and looks for cheap places to buy.

Lets us know Because there On my maybe list with Cpi's And some of GGR's drag pipes.

Reas11 Sorry for the off topic question. Have you ran the shearer and what do you think?

Nyuk where a good place to buy them. Proflow has them for 149.95 each; can this price be beat? What about Fit, I have A billet intake with no cross and my rs 34 fit ok will the TMX 35 clear my clutch arm OK with that manifold? Oh I received my Andy Weeks 5-inch over Swing Arm Friday. Thx for PR on GGR He Is Great Guy to work with.

Has anybody used the tmx 35mm Mikuni flatsides.

Cooker Dyno link only load the aroba reader. No pdf file