chetgoff

Thanks for the help. that is what I was looking for. I measured both cylinders and the deck to base was the same. I was thinking it was 104 or more also. I currently have t-5's. all I do is drag this thing in the sand. I never dune it just play at the drags so I have been trying to go that way with it. I have 35mm PWK carbs. the timing is +4. and the head is milled. not sure how much. I'm looking to get it drag ported if possible. I'm not sure what is up with the cylinder heights. the piston was not protuding the top of the cylinders. If I go drag ported will t-5's be ok or should I go with shearer's.. I'm not sure who ported them. I bought the bike done and the guy did not know. again thanks for the help.

I measured the cylinders deck to base is 102.5 mm Exhaust dect to bottom of port =55.5 and deck to top=29mm./ Intake is deck to bottom of ports=101.5mm and deck to top of port=67.2mm/ The port above the intake (not sure what it is called) deck to bottom of port= 60mm and deck to top of port=43.5mm/ side ports(again not sure what they are called) deck to bottom of ports=60mm and deck to top of ports =42. I will post some pictures of the cylinders just looking to see how they look and possibly what the ports are as far as a drag,dune or what.

how much for the pipes shipped to 93268

does it matter how it goes on. one side is flat and the other hase that grove in it

I'm looking for a set of drag a-arms either stock width or -2 or something narrower.

got mine on e-bay from driveline performances for 59.00 shipped I run there clutches and have no prob so trying there chains cant beat the pricwe.

I have a set send me your e-mail and I will send pics

my tirre size is 22x11x10 10 paddle extreme haulers I weigh about 250. maybe this will help to decide where would be good to start?

what length of shocks are you guy's running with a +6 swingarm?

I have a +6 swingarm and a stock length shock. It is way too soft. I'm looking at buying a marvin what would be a good length

Looking for input on gearing. I have drag ported cylinders, milled head 64.5 bore. stock stroke 35mm carbs boysen reeds with ported cages +4 timing +6 swingarm 10 paddle extreme haulers. T5 exhaust.. right now i'm stock gearing and all i ride is sand and 99% of the time playing at the drags. what is a good gearing starting point.

I'm in need of a marvin shaw for the rear. stock length.

PM'D

what I meant to say was just on i'm not worried about low and high. I just want on

ok guys have been searching but not finding the answer i'm looking for. I don't have a key and i'm wanting to get rid of the stock kill switch and lights. i'm gonna run pro design tether for kill but i want to put the lights on a toggle so if i ever want to run them I can. i'm only concerned with them being on night low beam and high beam. how would I wire this up.

how much for the front shocks

what transmission oil you guy's running?

Ok guy's I took apart my bike to put in the new shift shaft and star also new clutch and water pump. after reading on here i decided to go with mull water pump and drive gear. the problem is i have been waiting on water pump for over a month now. I have been asking them when they will be available and all i get is next week. I have a trip planned new years so just getting nervous. my question is is there another good one out there worth buying or should i wait. help me out.

http://cgi.ebay.com/ebaymotors/NEW-2006-YAMAHA-YFZ350-BANSHEE-NEW-CRATE-_W0QQcmdZViewItemQQhashZitem4cf27e6c5dQQitemZ330485886045QQptZATVs

hey guy's got a question. i'm replacing my water pump with the mull one so I will be keeping my original shaft. I pulled the old one out and the seal and bearing look to be in good condition. however don't wan't to put together and have a problem should I order new one's or is it save to rune the same one's just looking for what other people have done.

found these on e-bay has anybody heard of them and are they any good? also could you get bushings for them. http://cgi.ebay.com/ebaymotors/Omega-air-shocks-like-Fox-air-shocks-only-worse-_W0QQcmdZViewItemQQhashZitem3a5f746932QQitemZ250709567794QQptZMotorcyclesQ5fPartsQ5fAccessories That is an e-bay link

I'm running stock arms and plus 6 swinger mainly used for drag and dune quote name='800phelps' date='10 October 2010 - 07:54 PM' timestamp='1286758443' post='1175813'] you might want to include some details.... height, what they will be used for etc.

looking for a set of shaws

looking for a set of shaws