papa-smurf

I live about 45 minutes outside rochester in palmyra, i dont ride much in rochester but in palmyra where i live there is an old railroad track with 2 sand/gravel pits I ride on, basically my back yard. Someone has to want these cyl/pistons. Go to college on friday so if they aren't gone I'll probably hold onto them until further notice.

ok, rochester thx for the bump

Lookin' for a new stator for my banshee. I will consider buying a complete ignition (stator, coils, wiring harness) if it is reasonable. If anyone has either(working component) let me know via post or pm please. Thanks, Mike

Bump 100 + the ride

they are stock

Bumpity Bump. 120 obo

Hey fellas, Got some new cylinders and pistons so I am putting these up for sale. They do have some flaws though. I hail from the state of NY if someone is interested in a pick-up by chance. These cylinders came with the bike when I bought it used and a dumbass before me had tried to helicoil the studs but happened to drill the stud inserts too large and ended up using glue or loctite to hold the coils in there. There is also a case insert spacer stuck in the bottom of the same cylinder. The cylinders do look to be "ported" but I do not think they are professionally done. The pistons are in good condition, they look to have low hours (I rode with them for 5 min) I am looking to get $150 for them but will take any offers. heli coils Thanks for lookin! shoot a pm if interested Mike

sorry edit

sick bike man. props

Im lookin for a flywheel key and a clutch cover gasket. Anyone have any extras laying around? Smurf Daddy

can anyone let me know what i will need when i switch cases as far as other stuff to buy. I know Im going to purchase an oil seal kit from F.A.S.T. I have blue thread locker and yamabond 4 already. What else would be a good idea to replace while I have her gutted

sold

just bought a set of cases

may be interested after pics

its all good..if i happen to be in MI with my motor ill call ya

you can take every last piece off of that frame if you would prefer too. just try not to lose anything in the process.

im from ny. A lot of my underbody of the cases have oil leaking. I didnt know what it was supposed to look like, first banshee. If you would like me to take a pic of a different angle or area I could do that. Im just trying to figure everything out, I thought I had been pretty close to finishing my rebuild then I started putting fluids in and drippage from multiple places. The nuts/studs from the first pic and that area that looks welded. There are two holes under my engine, one you can see in the first pic above the two studs/nuts. What are those for?

thanks buddy lol

thanks i didnt know how to do that or else I would have

Its not done, still have to get black plastics and black wheels but here are some pics http://s815.photobucket.com/albums/zz79/supermdub/?action=view&current=001.jpg geez..flash really brings the rust out in pics haha..its not that bad in person http://s815.photobucket.com/albums/zz79/supermdub/?action=view&current=021.jpg sweet autobot grill from jdscustom

Oil Leak thread here is a link for the situation. There are also some pics of the studs that are leaking After exploring under my banshee a little more, I believe my under body of my case on the left side seems to be welded. Can anybody verify if this looks right or what the next action should be? http://s815.photobucket.com/albums/zz79/supermdub/?action=view&current=013.jpg these are the leaking studs, what are those holes for under the engine? They were full of grime before I emptied it http://s815.photobucket.com/albums/zz79/supermdub/?action=view&current=015.jpg idk what to think about it, is it supposed to be like that?

the oil saturates the studs and drips..there is no oil around the drain bolt

Hey guys..they are still leaking after trying to seal the nuts. The leak is at the two studs under the engine near the oil drain bolt. Do I have to go into the cases and replace gaskets/seals to stop this leak?

what would you charge roughly for a successful seat cover?