bbcmudtruck

Csrmel, thats hillarious! Totally messes with thier minds haha

Just fucking with ya. I have run the +2+1 full flights for 2 years now. I had one bend on a really bad crash, and they sent me a new one, no questions asked. If you go with the FFs get the chromoly arms and hiems. Ryan

Nice! I was a little surprised at the torque numbers though. How much torque can you get out of a banshee motor? Ryan

You need to practice your searching, I got this page to show up on the first try! http://www.bansheehq.com/forums/index.php?...%2Bfull+flights

Haha, I was bidding against you! Send them to works.

Send them to Kevin! http://www.herrjugsracing.com/index.html

Will a durablue axle out of a warrior fit the banshee stock carrier? Thanks Ryan

What do you call an open can of tuna in a lesbians house? Potpourri.

I have +2+1 arms, can I put the 300ex shocks on there, or will it be too low? I am only putting the shocks on to race on the weekends. Also, will the 300ex rear shock work in the rear of the banshee? Thanks Ryan

Where are you located? Ryan

Kevin is the go to guy. If you are looking for a builder who will take the time to answer all of your idiotic questions and never get frustrated, hes your guy. His costumer service is among the best, not to mention his lightning speed turn around time! I was very close to parting the shee out and cutting my loses. Kevin went above and beyond the call of duty to get me going once more. Ryan

I have no idea what deck height is or squish let alone how to check it. I could not find it in the manual anywhere. The base gasket measured .021 after being used. The compression guage is correct, I double checked it with another gauge. I performed the compression check correctly. Here is a pic of the piston skirt after 1 hour of ride time. Is it F'ed? Thanks for the help so far guys. Ryan

I tore down a good running motor to send out for a dune/hillshooter port job and freshin up. The builder said that they did not need a new bore and honed them. While I had it apart I got some T5s, cool head and a timing plate. When I put it together I was expecting a significant improvement, but it runs no better than it did with a stock port and Fattys. I am having trouble with compression. I first put on a stock head it had 60psi per cylinder. So I put on 21cc domes and a coolhead it had 100psi. Then I put in 19cc domes and it now has 130psi in each cylinder. The ring gaps are within tolerance at .012. The jetting is really close at 330 and 27.5. I tore it back down and after 1 hour of run time I have a scuffed piston. I was running against a 400z and it was right on my ass everytime. It has little to zero bottom end, and bogs between gears. I have been Fn with this POS for over a month, and have missed half of the race season because it. Any ideas of what to try next? Ryan

I got some 21s and 22s in good shape $45 shipped for each set. Ryan

DUI Missouri Style Body: Only a person in Missouri could think of this. From the county where drunk driving is considered a sport, comes this true story. Recently a routine police patrol parked outside a bar in STL, MO after last call the officer noticed a man leaving the bar so apparently intoxicated that he could barely walk. The man stumbled around the parking lot for a few minutes, with the officer quietly observing. After what seemed an eternity in which he tried his keys on five different vehicles, the man managed to find his car and fall into it. He sat there for a few minutes as a number of other patrons left the bar and drove off. Finally he started the car, switched the wipers on and off--it was a fine, dry summer night--,flicked the blinkers on and off a couple of times, honked the horn and then switched on the lights. He moved the vehicle forward a few inches, reversed a little and then remained still for a few more minutes as some more of the other patrons' vehicles left. At last, when his was the only car left in the parking lot, he pulled out and drove slowly down the road. The police officer, having waited patiently all this time, now started up his patrol car, put on the flashing lights, promptly pulled the man over and administered a breathalyzer test. To his amazement, the breathalyzer indicated no evidence that the man had consumed any alcohol at all! Dumbfounded, the officer said, I'll have to ask you to accompany me to the sherriffs office. This breathalyzer equipment must be broken.' 'I doubt it,' said the truly proud non-drinker. 'Tonight I'm the designated decoy.'

Has anyone ever seen or mounted a cooling fan on a shee? It would be tits to be able to flick a toggle in the trails and run a fan.

I'll vouch for him, I bought a Noss head from him. He is legit. You do have a ton of heads for sale, whats up with that? Ryan

I still got first dibs, I never heard back from this kid.

Where are you located?

I second that. He hooked me up on some domes! Thanks man! Ryan

I have a six pack rack made by PRM. I don't know if I figured the shipping correctly, but ups wants $85 bucks to ship the dam thing. I want $30 bucks for the rack, its up to you to figure out the shipping. Ryan

Thanks for the heads up scooter, but I just bought some off of another guy on here. Ryan

Ill take second dibbs. Ryan

I think you need to turn your air screws in or go to 27.5 pilots. If your running good on the top you main is good, I'm guessing a little rich. If its running bad at 1/4-1/2 you need to adjust your needle clip. Ryan

^^UP^^