Jump to content

dekker

Members
 View Profile  See their activity

  • Posts

    314

  • Joined

  • Last visited

 Content Type 

Everything posted by dekker

  1. dekker
    To do a propper compression test you need to hold the throttle wide open and kick till the guage stops climbing. Your compression will vary with your elevation. The 140 something sounds about right Zach
  2. dekker
    If its decent ill probably be there... I think im gonna try to go this weekend looks like it will be in the 50's and sunny..... I got the itch to hit the sand real bad
  3. dekker
    take the fitting out and put your finger over the hole let off when you pump then put your finger back over the hole when you release the lever. once you get a good flow put the bleeder back on and pump a couple more times then lock it up tight .... worked for me
  4. dekker
    If the reeds are not sealing IT will run LIKE SHIT
  5. dekker
    I dont know man if you want me to stop and give you a hand let me know
  6. dekker
    Sounds good to me Paypal to [email protected] send me your adress info
  7. dekker
    Did you try dropping the main.... checking your petcock screen for blockage that would restrict the fuel flow???? Clean the carbs real good with compressed air sounds like you have done most of it .... definately seems like a fuel problem to me too
  8. dekker
    I would think that black spray would work just fine. they make it for plastic I say do it up
  9. dekker
    100+ shipping or they are goin on fleabay -Zach
  10. dekker
    I have no idea man i got them fall last year dont remember where they came from for sure
  11. dekker
    Some old school fmf pipes they need to be polished up bc of surface rust or blasted and painted some minor dents i got them off ebay and never ran them.... 125.00 obo +the ride Zach
  12. dekker

    Intakes

    dekker posted a topic in Wanted

    Looking for some intakes that will fit 34 mm carbs let me know what you have Zach
  13. dekker
    Bad crank seal oil pulling into the crankcase and burning
  14. dekker
    The expasion chamber pipe should slide inside the stinger pipe. try shifting the expansion chamber around some and see if you can get it on there. Mine fit with no problems. Zach
  15. dekker
    Joel Here is a pic of my bridge to compare I think yours is as thick if not thicker than mine they should be fine Zach :beer:
  16. dekker
    There is a cross over tube that goes in place of the boost bottle .....
  17. dekker
    I think it looks just fine
  18. dekker
    Here are the pics of his bridge Zach
  19. dekker
    Anyone????
  20. dekker
    Picked up a set of 34mm tmx mikunis just wondering where to start my jetting. I ran 360's on my stockers my mods are in my sig.... I was thinking go up 3 or so sizes to start any help would be much appreciated. Zach
  21. dekker
    PM sent
  22. dekker
    Many different gasket makers use different materials I have seen the paper type you are talking aboutand I know some base gaskets have metal in them and you can get different thickness..... I had metal base gaskets with the coating over them and I actually prefer them to the paper ones. You will bejust fine Zach
  23. dekker
    Many people will knock fatties but In my opinion and from experience for they money they are a great all around pipe... I cant speak to the others because I have not ridden bikes with them
  24. dekker
    Take the clutch cover off and there is a screw and a nut that run directly through the middle of the outer pressure plate all the way in and makes contact with your ball and rod loosten the lock nut and turn the screw in when you get it to where you want it tighten the lock nut .... MAKE SURE IT IS TIGHT and then put her back together..... all done really easy
  25. dekker
    Those are not skat trac haulers but they look like the ones that were on ebay I think they are almost exactly the same though...... I have a set of the ebay ones and they hook really hard good tire good price

BHQ Quick Links

×
×
  • Create New...