TeamBigginRacing

someone??

There is a rubber o ring that goes on the back of the clutch housing..was not there when got the bike!Clymer book pg.156/chapter six-- #17 do i need??????????

i have a set of pro tapper bars i would like to put on my shee...can anybody tell me if these clamps would work?? I asked the guy but didn't know! TY for any info! http://cgi.ebay.com/ebaymotors/ws/eBayISAP...TRK%3AMEBI%3AIT

coil^^^^^and could b stater fleabay or get new one should b it!!!

send me a pix see how much to ship to [email protected]

32:1..^^^^^^what kind of oil mix r u running?

Yeah same here on the jets...i kept seeing everybody on here talk about 200+300+ i was like wtf mine's only in the 100's...o-well fig that out tho...i've seen the newer carbs pwk with the 2 screws ,..or it might be honed out to 30's......

mild dune/trail port job at least thats what i was told...don't look to be to much porying but still rips and everything dialed in perfacto

someone said usein stock clamps work better....don't matter witch u use your going to rip that boot 1 way or another(airleak) .2

yeah i like mine i have 28 i got new from magicracing they were set up already to go on the bike when i got mine pre jetted and everything...i seen a few forums tho that people said they didn't like them! i like mine just my .2cents ...mine came with cable

yeah i wouldn't bore...just thinkin if it's going to be faster or will he need to do some up grading....me i thinking about getting the modded shift star or modding mine..and the shift pro...+2 or 4 swinger and going up to a 15 t on the front,.. going thru gears to fast on a 14t and wheels won't stay down!!! do u think i should go to a bigger carb set up?

HOW BIG OF A HP GAIN IS IT FROM BIG BORE/ OR PORTING? I HAVE A PORT JOB ON MINE AND I'M IN THE PROSSES OF BULIDING ANOTHER FOR A BUDDY THAT HE GOT FOR $500...THE GUY THAT SOLD IT WAS 2STROKESTUPID...SAID HE PUT $1000 IN LOWER HALF ECT...SOLD IT FOR 5???? ANYWAYS MINE IS @ STOCK BORE AND SHEE RIPPS WITH THE PORT JOB I GOT FROM K&T...MY BUDDY HAS A BIGBORE KIT AND ITS @ 1.00 OVER HOW MUCH DIFF IS IT GOING TO B? ALOT OR A LITTLE MINE WORK IS IN MY SIG HIS WORK IS BIG BORE KIT 1.00 NO PORTING..STOCK REEDS..K&N PODS PRO DES.COOLHEAD 22 DOMES AND PRO CIRCIT PIPES FRONT AND BACK! WHAT DO U GUYS THINK?

Whats better the shift pro or this(modded star)? and ..i have book but is it hard to install??

hey thanks i think ill try both...i got stuff off u on e-bay, and your link @ the bottom of your page has a virus...whats up with that??? check it out!!! xcbob.com

i seen that there is something for the header pipe that hooks up to the cly...that will plug better them the stock o-ring??? could someone send me a link or something! TY

how big of a diff dose it make??

Need the stock inner hub for the clutch ass..let me know plz

i was sayin ALL out OF BORES FROM STOCK!!

very nicely put!!!

go 15...u can go 14 but i think u'll want to go 15..

i have a cover...stock like new

E-BREAK!!!!!!!!!!!!!!!!!!!!!!99%

66.50 is all out stock...i have 66.25 and the jugs r @ 66.00 http://www.wiseco.com/PDFs/Catalogs/CB06/YamahaATV.pdf Piston kit includes pistons, rings, retainer clips, piston pins, and gasket. $238.11 MAKE OFFER!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

ok never heard from

OZZFEST IS THE SHIT!! I'VE SEEN THEM HERE IN MICHIGAN THE LAST FEW YEARS..THE FIRST 1 I SAID I WOULD NEVER MISS IT AGAIN!!!! DISTURBED ROCKS!!! CHICKS WITH NO SHRITS ON PAINTED UP GIVES U SOMETHING TO LOOK AT BETWEEN SETS AND BEER RUNS!!!