Rescuejeff

I run a +4 setting on my Ricky Stator with a mix of 100 low lead AV gas and pump with slightly more than normal mix in the gas, I run the fuel mix 50/50.

No I don't have a PM, thanks for answering my question as you all answered it very well. I will just drain and flush each year.

But no answer on whether I need to worry about additional wear to the case and if the floating particles in the anti freeze pose any risk?? Thanks

Send me a picture of each bumper...Thanks

I'm looking for a stock front bumper that is NOT dented and not bent in any way. I would like to chrome it so damage to it would make it unuseable for me. Thanks.

I'll take some pictures of my A-Arms that where custom made for me by IMS some time ago, I'm not sure if they are still selling them or not. Check back on Monday. Sorry got hung up at work check tomorrow, Tuesday

Just out of curiousity, have you adjusted down the ring that is threaded on the shock toprovide some rebound/stiffness to teh shock and maybe you have the preloading too soft or the valve too soft...ideas.

Hey I got a question for you folks out here. I have a older banshee, 1989 and I'm replacing water seal, bearing and impeller just for insurance. I have looked at the all metal impellers, but worried about wear to the side case and what the floating parts form wear are going to cause in the seal and loading up the raditor. I would like to hear from anyone that has had good and bad experiences from the swap. Thanks

I had a fit issue with them and dealt directly with ITP and they had all the info, give them a call or look on the website.

Like everyone else said, stay with what you have and do othermods like lightened fly wheel(big difference), mod your timing plate, pipes, vforce reeds and mill the head. Good luck

Like everyone else said, stay with what you have and do othermods like lightened fly wheel(big difference), mod your timing plate, pipes, and mill the head. Good luck

I had my wifes frame, swing arm(rear), inner front disc brake guards, and bearing career done in San Diego for $225. Just a reference, I hope yours is cheaper.

Just buy a kit from Pro motion, at Rocky mountain or your local stealership.

I don't think that the 6-series will fit a banshee, but they are stronger. The normal c-styles are very good, had no problems since i put them on the wifes quad last year.

I had the rear revalved and what a difference, like a whole new bike, look in to it. I have Precision Concepts do mine. Lates..

You can get 525 or 530 chain specially cut for you, but you will be paying about twice the cost. You should look in to Vortex sporkets. I have them on my bike and I have had them running two years with about 15 desert trips. Good luck

Thanks your the bomb. Have a great day.

I took his five wired plug off his CDI and pushed the pins through so I could wrap my plugs wire around his to run it to test that my cdi was bad. His has the four wire(white/red, whitegreen, red and green) then another plug with (black, Black/white, orange, red with a strip and green). I figured out the green(since I never took it loose, but found the location of the orange and black/white wires through a picture, but it did not show me the red or black wire. So can you tell me which goes between the orange and green wire?? Thanks again

I borrowed a friends CDI to test mine out and pushed his pins throught to hard wire my plug on since he has a newer shee then me. He has a 3GG-10 with a four and five wire plugs. I need to know th e configuration of the five wire plug. I know where green and orange and black/white goes but where does the red go, next to orange or black /white??? Thanks in advance.

I have a stator out of a 89 that I just updated to a 200w systems, what do you think it's worth???

Ok, I'm stupid... I need to look at the persons asking the question. I have digital pictures I can email you tomorrow if you like, email me your address.

I have the complete set of J and lower A rms for sale if you like off a 89 banshee that is silver in color. Email a price you think they are worth. They have been used on the sand only, by a wife that is 105 lbs. I have the stock shocks as well if your interested, they have red coils. I have no idea what shipping is, but I'm in Southern California.

Will the rims fit a banshee?? I need the two back rims for a shee. Thanks

I have a complete set of 89 J and Arms set that has no damage and is painted silver. Stock shocks that are still in good working order, came off the wifes bike, she is 105 lbs, so not worked over. I may be interested in trading for some other parts like front bumper with no dents.

Front bumpers for the shee, does the one off the 04 fit a 89??? If so I would be interested in it. Thanks.