junkyarddog Posted April 29, 2016 Report Share Posted April 29, 2016 Just got these gave to me and there about to go to get bored, I'm looking for ideals to fixing this Small gouge so the gasket will seal? What are some good Apoxsee? Or what else works good? What do they use to apoxsee when trenching maybe that is what I need? Quote Link to comment Share on other sites More sharing options...
trickedcarbine Posted April 29, 2016 Report Share Posted April 29, 2016 Uhh..... Photo? Moroso and Devcon make good epoxy. Quote Link to comment Share on other sites More sharing options...
sheerider11 Posted April 29, 2016 Report Share Posted April 29, 2016 Apoxsee. That's a new one 1 Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted April 29, 2016 Author Report Share Posted April 29, 2016 Sent from my iPad using Tapatalk Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted April 29, 2016 Author Report Share Posted April 29, 2016 Crap here's the pics I Forgot Sent from my iPad using Tapatalk Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted April 29, 2016 Author Report Share Posted April 29, 2016 Ya epoxy, lmao I talk and let the phone typ when working sometimes it gets creative Quote Link to comment Share on other sites More sharing options...
sleeper06 Posted April 29, 2016 Report Share Posted April 29, 2016 I use marine Tek grey Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted April 29, 2016 Author Report Share Posted April 29, 2016 This? Quote Link to comment Share on other sites More sharing options...
junkyarddog Posted April 29, 2016 Author Report Share Posted April 29, 2016 Sleeper06 I have had a few people bring your name up for porting cylinders, message me if you have any interest in doing some stockers Sent from my iPad using Tapatalk Quote Link to comment Share on other sites More sharing options...
Big Mike NY Posted April 30, 2016 Report Share Posted April 30, 2016 He'll make your stock cylinders eat lighting and crap thunder!!!! 2 Quote Link to comment Share on other sites More sharing options...
Big Mike NY Posted April 30, 2016 Report Share Posted April 30, 2016 (edited) Someone shit in your pasta on the TRX forum? Edited April 30, 2016 by Big Mike NY Quote Link to comment Share on other sites More sharing options...
registered user Posted April 30, 2016 Report Share Posted April 30, 2016 quit being a nutswinger mike junkyarddawg, devcon is good but expensive ($50 for the smallest quantity) and takes a week or so to get. if the unused portion isn't sealed very well then it goes to waste. moroso is fine but $35 and its doubtful youll find it around town unless you have a automotive speed shop. go to ace hardware and get jb weld steel stik putty. about $8 and put the remainder in double Ziploc bags 1 Quote Link to comment Share on other sites More sharing options...
sleeper06 Posted April 30, 2016 Report Share Posted April 30, 2016 He's not really being a nutswinger, I'll put my stock cylinders up against anyone including you . There's not many people squeezing power like I am with ridability . As for the op that's the stuff I use marine Tek all the time , as with everything prep is where it makes ands breaks a project . Pm if you need anything 6 Quote Link to comment Share on other sites More sharing options...
Redline Racing Posted April 30, 2016 Report Share Posted April 30, 2016 Why not weld it up deck cylinder back down and never worry best choice. Epoxy will be so thin it will be easy to chip off or scrape when cleaning gaskets. It's between both cylinders so put good cyl on first put a small bead of 1211 between cylinders and install damaged cyl. It will never blow since they are right next to each other. 1 Quote Link to comment Share on other sites More sharing options...
locogato11283 Posted April 30, 2016 Report Share Posted April 30, 2016 Why not weld it up deck cylinder back down and never worry best choice. Epoxy will be so thin it will be easy to chip off or scrape when cleaning gaskets. It's between both cylinders so put good cyl on first put a small bead of 1211 between cylinders and install damaged cyl. It will never blow since they are right next to each other. This. Unless you feel like fucking with it more than you need to. Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.