2strokersteve Posted January 29, 2006 Report Share Posted January 29, 2006 (edited) stock with pro circut pipes and K&N fitlers no airbox were should I be and what needle poss. are you guys running going there in 3 weeks thanks steve Edited February 12, 2006 by 2strokersteve Quote Link to comment Share on other sites More sharing options...
dnhyoung Posted January 29, 2006 Report Share Posted January 29, 2006 It really depends on your bike, and how it is set-up. You can't really take someeon elses setting and just throw it on your bike. What are some of your mods, and I'm sure some can help get you close. Also it will depend on the weather. since it can vary quite a bit. what elevation are you running at now?? Quote Link to comment Share on other sites More sharing options...
wesw Posted January 29, 2006 Report Share Posted January 29, 2006 odaen is from around there he can help you out. Quote Link to comment Share on other sites More sharing options...
odaen Posted January 29, 2006 Report Share Posted January 29, 2006 stock with pro circut pipes and a K&N were should I be and what needle poss. are you guys running going there in 3 weeks thanks steve 466041[/snapback] Prolly lookin at a 27.5 pilot Toomey Needle in 3rd clip 250ish on the main if you are running a lid, 290 without Someone might get you closer, I've always run the K&N clamp on pods. Quote Link to comment Share on other sites More sharing options...
2strokersteve Posted February 11, 2006 Author Report Share Posted February 11, 2006 Prolly lookin at a 27.5 pilotToomey Needle in 3rd clip 250ish on the main if you are running a lid, 290 without Someone might get you closer, I've always run the K&N clamp on pods. 466105[/snapback] im now got some k&n clamp ons 290 mains? where do i get toomy needles can i just use stock needles ? and is the pilot where the main screws into or where is that? thanks for the help guys Quote Link to comment Share on other sites More sharing options...
2003LimitedBanshee Posted February 11, 2006 Report Share Posted February 11, 2006 im now got some k&n clamp ons 290 mains? where do i get toomy needles can i just use stock needles ? and is the pilot where the main screws into or where is that? thanks for the help guys 472012[/snapback] With the clamp-ons I would suspect you should be more near to 330 range. You can use the stock needles, it seems to be much more personal preference than anything else. I would say 3rd clip on the stock needle, 4th if you step up to the Dynojet (included with Toomey kit) needle. The pilot jet sits in the casting right next to the main jet. The plastic guard/guide piece that fits around the main, where the tab goes down into the carb, that is where you will find your pilot jet. I ran a 27.5 pilot at 1.75 turns, but recently went back to the 25 (stock) pilot w/.5 turns out on the air screw after installing my VForce3's and noticed significantly better throttle response than immediately after the VForce install with 27.5's. I run this setup at Horsfall (Coos Bay/North Bend) flawlessly. Quote Link to comment Share on other sites More sharing options...
2strokersteve Posted February 12, 2006 Author Report Share Posted February 12, 2006 I would say 3rd clip on the stock needle 472037[/snapback] that would be 3rd clip from the bottom so one showing from the top right? Quote Link to comment Share on other sites More sharing options...
yellabanshee Posted February 12, 2006 Report Share Posted February 12, 2006 where do you ride now......wher are you from? and what works there? Quote Link to comment Share on other sites More sharing options...
ogre03 Posted February 12, 2006 Report Share Posted February 12, 2006 that would be 3rd clip from the bottom so one showing from the top right? 472099[/snapback] Third clip position down from the blunt end. That's one one slot showing on the pointed end. Quote Link to comment Share on other sites More sharing options...
2strokersteve Posted February 12, 2006 Author Report Share Posted February 12, 2006 (edited) where do you ride now......wher are you from?I live in north west part of washington st and what works there? I dont know I havent had a banshee for five years this is a new project what ever works in florence works here Im going there in april just trying to get organized. 472154[/snapback] Edited February 12, 2006 by 2strokersteve Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.