trueblue Posted September 22, 2005 Report Posted September 22, 2005 I was wondering if my banshee will beat a raptor 686? my banshee is ported by rudy kurtz, wiesco prolites, coolhead with 18cc domes, v-vorce3 35 mill carbs and toomey t-5s. Also if i was to do a 4mill crank what would i have to do or get besides raising the ports and what type of performance gains would i see. Quote
trueblue Posted September 23, 2005 Author Report Posted September 23, 2005 i tried but could not find anything Quote
reded Posted September 23, 2005 Report Posted September 23, 2005 Your best bet might be to sell the Toomeys and buy a set of inframe drag pipes. They will wake it up for sure. Quote
Z28ROC Posted September 23, 2005 Report Posted September 23, 2005 Don't know what kind of racing you're talking about, but with your mods, you shouldn't have much trouble with the Raptor up a sand hill. Quote
bobbybonilla Posted September 23, 2005 Report Posted September 23, 2005 (edited) You should hand the raptor its ass about anywhere, as long as you get nice traction. Its only a 686. You should walk all over the new raptors too and they are 700cc fuel injected. Edited September 23, 2005 by bobbybonilla Quote
05bansh Posted September 23, 2005 Report Posted September 23, 2005 Of coarse you will beat the Crapter, even if it is a 686. No doubt about it. Unless you are a horrible rider........ Quote
bansheeryder_69 Posted September 23, 2005 Report Posted September 23, 2005 Unless you weck you shuld walk all over the heavy ass craptor Quote
locogato11283 Posted September 23, 2005 Report Posted September 23, 2005 Your best bet might be to sell the Toomeys and buy a set of inframe drag pipes. They will wake it up for sure. 418180[/snapback] word... You should hand the raptor its ass about anywhere, as long as you get nice traction. Its only a 686. You should walk all over the new raptors too and they are 700cc fuel injected. 418224[/snapback] even the new 700r craptors arent 700..just a plain old 686...only thing thats considerably different is the efi that isnt gonna make it faster, just start easier.... Quote
Ducman Posted September 23, 2005 Report Posted September 23, 2005 I have seen a 80 HP 700cc built raptor that would hand you your ass but if its just the run of the mill piped craptor then as long as you get good traction he's dust. Quote
helldriver Posted September 24, 2005 Report Posted September 24, 2005 well i have a 686 raptor with all the goodies,, cam, piston, valves, etc, and it will beat a stock shee, and give a shee with just pipes a good run, until the shee hits 5 and sixth gears, than all i can do watch as the Shee puils away Quote
Koolguyson Posted September 24, 2005 Report Posted September 24, 2005 if its a true port magic motor even an 80hp raptor shouldnt "hand you your ass" rudy does good work and just call him and he will tell you how your motor is set up. His motors like cpi's and shearers, not t-5s. a 4mm needs to be reported and the domes re-cut Quote
Ducman Posted September 24, 2005 Report Posted September 24, 2005 well i have a 686 raptor with all the goodies,, cam, piston, valves, etc, and it will beat a stock shee, and give a shee with just pipes a good run, until the shee hits 5 and sixth gears, than all i can do watch as the Shee puils away 418562[/snapback] Sorry Bro, banshee's just haul ass. No seriously, I think your being a slight bit humble since your an a banshee forum. But we appreciate the integrity. Quote
thegroup Posted September 24, 2005 Report Posted September 24, 2005 well i have a 686 raptor with all the goodies,, cam, piston, valves, etc, and it will beat a stock shee 418562[/snapback] my 95 warrior with all that (still 350 stroke) will beat a stock 'shee before the crank went out Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.