n2otoofast4u Posted April 7, 2013 Report Posted April 7, 2013 M671504 touched it briefly, but I've seen on multiple occasions where the float actually rubs the billet bowls and hangs them up. Lastly. For future notes. Anything lectron that's going to be used on alky goes to Dennis. When you have them apart snap a picture of the metering rods and make note of what number/letter they are. Quote
CAJUN BANSHEE Posted April 7, 2013 Author Report Posted April 7, 2013 Pe-1 rod set at 48.6. I shouldn't have to use a speacial throttle cable for these carbs right? 1 Quote
CAJUN BANSHEE Posted April 7, 2013 Author Report Posted April 7, 2013 This should be the right top and cable adjustment. Quote
CAJUN BANSHEE Posted April 7, 2013 Author Report Posted April 7, 2013 M671504 touched it briefly, but I've seen on multiple occasions where the float actually rubs the billet bowls and hangs them up. Lastly. For future notes. Anything lectron that's going to be used on alky goes to Dennis. When you have them apart snap a picture of the metering rods and make note of what number/letter they are. Like this? Quote
n2otoofast4u Posted April 7, 2013 Report Posted April 7, 2013 what size are the needle/seat? Those PJs are pretty special as well.. Will probably work, but not quite what I was picturing.. Did They put those in or were they already there? Quote
CAJUN BANSHEE Posted April 7, 2013 Author Report Posted April 7, 2013 If this is where they normally hang up should I shave the sides of the bowl with a dremel? Quote
CAJUN BANSHEE Posted April 7, 2013 Author Report Posted April 7, 2013 what size are the needle/seat? Those PJs are pretty special as well.. Will probably work, but not quite what I was picturing.. Did They put those in or were they already there? Pjs were there and seat is 3.5 Quote
rjdgriff Posted April 7, 2013 Report Posted April 7, 2013 Get some pwks You are a idiot. It's you are an idiot, not a idiot, you idiot Quote
Nieskes Posted April 7, 2013 Report Posted April 7, 2013 Nope, you are a idiot. And im pretty sure you like dick in, or around your butthole..... Quote
CAJUN BANSHEE Posted April 7, 2013 Author Report Posted April 7, 2013 Anyways, those are interesting looking PJ's. What's the benefit or reason to them being like that? It's not bothering me, it actually put a grin on my face while I'm trying to figure this shit out. Dunno bout the pjs, I'd have to ask the guy that screwed me over on these. Of coarse it was last summer when I bought em. My fault, I should have checked them out closely. Quote
Surfrjag Posted April 7, 2013 Report Posted April 7, 2013 Packards pj are like the ones i pictured Quote
n2otoofast4u Posted April 7, 2013 Report Posted April 7, 2013 the middle pj is similar to a clippard and should work fine. the other is a pill style that uses a round main jet to control flow. The setup will work, just no what I was expecting to see Quote
CAJUN BANSHEE Posted April 7, 2013 Author Report Posted April 7, 2013 the middle pj is similar to a clippard and should work fine. the other is a pill style that uses a round main jet to control flow. The setup will work, just no what I was expecting to see Ya think this is like an old school set up or something? Or a hack job? Evidently it'll work cause they were flow tested at Lectron, surely they would have mentioned it? Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.