enFORCER

I felt that I may need to add my opinion. What follows is a set of observations I have made about feeble-minded, manipulative self riotous immature members on this forum. Some members have -- not once, but several times -- been able to promulgate partisan prejudice against others without anyone stopping it. This kind of behavior should be put to a stop by the Moderators. However, their are times it seems that they (the Moderators) are the one's instigating the problem. Other times they seem to turn a blind eye, because the perpetrator is a friend. How long can that go on? As long as these capricious, sinful bromides are kept on life support. That's why we have to pull the plug on them and provide an antidote to contemporary manifestations of irritable sensationalism on this site.

Yep,I'm a fan! Every time I hear ( Kickstart my heart ) I think about ripp'n around on my Banshee!

Well these people want to put an end to all pubic riding areas. And they will use any and all reasons like environment, pollution, noise, ect!!!! Click here

I ride at St. Joe state park Missouri. Sand and woods. Bring your paddles if ya like to drag race.

Why? Are you planing on adopting some children?

You can get them from : Bob Tracey's world of cycles. Phone # (412-269-9999)I use the Barnett steel's , but the Barnett friction plates are junk. I'm running a lock out with the Yamaha street bike friction plates and Barnett steels. Part# for the friction plates are: 4H7-16321-02 Part# for the Barnett steels(drive plates) are: 2012-240

You can install a 4 mill stroker kit with out doing any case modifications. Anything bigger than 4 mill and you will need to have your case's trenched. You might want to put some bigger carbs on as well. 28mm or 30mm keihins would work. I see you have already advanced your timing about 4 degrees. You could have your flywheel lighten.....

Well nitromethane will turn a good motor to junk real fast!!!! But if you are going to try it, start with about 7% and go up 5 sizes on your jets. I am asumming you are running alcohol, because nitromethane does not mix with gas. There for you will most likely be drilling your jets out.If your not running a fuel pump, then you will need to get one. Hope you don't have a nice set of chrome pipe's. Because nitro burns so slow that it will blue your pipe's the first time you start it up. Unless you have money to waste, then I would stay away from it....

I run Klotz flex drive 30....

There's a few fast quads at St. Joe state park.... Better pack a lunch...

St. Joe state park is about 80 miles south of St. Louis... Lots of sand and woods.... It's a real nice place to ride.. Theres a few drag racers down there, if your into that

Boost Bottle, Bah ha hhahahahhahahahhahahahaha hahahahahahhahahahahahhahahah hahahahhahahahahahhahahahahhahaha hahahahahhaha ahhahahahhahahahahahhahahahhahahahahha. Ya know if you buy after market cylinders like a Cheetah, the intake has no holes for them. And I might add that on my old drag 350 I removed the cross-over tube and installed plugs......

Well you just tell that kid. The Banshee is good for going fast and looking really good while doing it!

I have a KLX110 pit bike.... I like www.planetminis.com

Starting to get kinda cold around here. I find that as I get older, riding in the snow just isn't as much fun as is was back in the day...... So how cold is to cold to ride????????????

I have one off my 04. In perfect condition.

You can 100+hp out of a 4mill if you spray it..........

Woooooo, sorry DuDe!!!!!!!! I didn't mean to step on your little bitty ego

LOL, well I don't think we made 420_Big-Bore's decision any easier......

Hmmmmm, aren't you the guy who has people swinging from your "balls"???? I think I read something like that a while back.... Anyway perhaps there is just not enough room for anyone new. So now people are turning to loco.......

ggr 0r shearers do not out perform CPI pipes...... If you are going to make a bold statement like that, you should back it up with a dyno graft. Now having said that, I must say that I do not like the ( power pro ) pipes either. Also, I know a guy who has shearer pipes and he is switching to CPI. He's not on this site. However he is on PS and his screen name is" RDZ350"... He would not be switching to CPI pipes if he thought the shearers were better....

I am running CPI drag pipe's on my 10 mill cheetah. They make real nice power all the way from bottom to top......

WoW DuDe!!!!!! With that big head of yours, how do you find a helmet that fits?????

yep, thats what I'm running.... 74.5mm bore x 64mm stroke... I run flat drags.... So far I haven't had a cub come close.....

Are you guys talking about Pope Benedict XVI the Nazi??? My this man has come a long way in life..... He joined the Hiltler youth when he was 14.... And now he's Pope! And now when he gives orders, the other Cardinals must respond Sig Heil, mein Fuher!!!!!