Columbus350 Posted May 2, 2017 Report Posted May 2, 2017 (edited) Ok so mods are 4mill crank Ported cylinder Cool head 28mm pwk CPI pipes Chariot billet intake with crossover V-force 4 Don't know pistons just bought ? Compression is at 148-150 It has oem key and timing plate set at 0 degree .....question is I'm getting a chariot plate can I advance it +4 and be ok on 91 pump with my mods????? Pros chime in thanks Sent from my iPhone using Tapatalk Edited May 2, 2017 by Columbus350 1 Quote
ClaudeMachining Posted May 2, 2017 Report Posted May 2, 2017 Usually, +4 is pretty safe for any setup. You are close to the edge on pump gas at 150psi. So yes, crank it to +4. But I'm not a pro, someone will correct me if I'm wrong. Envoyé de mon SM-G935W8 en utilisant Tapatalk Quote
LukeSandiefer Posted May 2, 2017 Report Posted May 2, 2017 I'm no pro, but you can definitely run pump 91 octane with around 150 lbs of compression and +4 timing. It's a good mod to boost and support your other mods. Almost all the engine builders will recommend it. Quote
bigweav81 Posted May 2, 2017 Report Posted May 2, 2017 Any idea on your porting? Sent from my SM-S820L using Tapatalk Quote
Columbus350 Posted May 2, 2017 Author Report Posted May 2, 2017 (edited) I should be good for pump gas I read that 165 PSI is the limit, as far as my porting I was told it was a trail Port but by the looks of it A 12-year-old could have ported my cylinder because there is Nick's and gouges here and there , but then again I've never seen a professional banshee cylinder ported , so I don't know what to compare to comparing it to a. Very familiar to me four stroke ported head does not look very clean I should have taken pictures, but overall it looks decent I wish I could get more info OK so it sounds like I will be OK running 4° extra Sent from my iPhone using Tapatalk Edited May 2, 2017 by Columbus350 Quote
trickedcarbine Posted May 2, 2017 Report Posted May 2, 2017 Static is more like a rough guide. But if a fella does enough of a particular combo, they can tell what is what by using static compression, but it takes experience. Not just a magical number. That said, what's the full motor combo? All specs? Quote
Columbus350 Posted May 2, 2017 Author Report Posted May 2, 2017 Static is more like a rough guide. But if a fella does enough of a particular combo, they can tell what is what by using static compression, but it takes experience. Not just a magical number. That said, what's the full motor combo? All specs? like I said I just picked this bike up , wish I could say I built the engine but I didn't. Don't know what domes it has. Or what compression pistons are, or squish all The specs I do know or listed above and the compression test results . So what would you say would be the safe thing to do leave it on stock degree until I do my next top end build , or turn it up now Sent from my iPhone using Tapatalk Quote
ClaudeMachining Posted May 2, 2017 Report Posted May 2, 2017 Put it at +4 and be done with it. Envoyé de mon SM-G935W8 en utilisant Tapatalk Quote
trickedcarbine Posted May 2, 2017 Report Posted May 2, 2017 like I said I just picked this bike up , wish I could say I built the engine but I didn't. Don't know what domes it has. Or what compression pistons are, or squish all The specs I do know or listed above and the compression test results . So what would you say would be the safe thing to do leave it on stock degree until I do my next top end build , or turn it up now Sent from my iPhone using Tapatalk Pull the head and figure out the domes. Also is the exhaust port opened up? But if its stock cyl , 4mm making 165 psi and the exhaust is ported, you may need to be running highER octane. 1 Quote
Columbus350 Posted May 3, 2017 Author Report Posted May 3, 2017 Pull the head and figure out the domes. Also is the exhaust port opened up? But if its stock cyl , 4mm making 165 psi and the exhaust is ported, you may need to be running highER octane.i'll check the exhaust ports it is a Stock cylinder 4 mill making 150 psi not 165 Sent from my iPhone using Tapatalk Quote
Columbus350 Posted May 3, 2017 Author Report Posted May 3, 2017 Also i don't want to pull head until it's time for rebuild , The last owner was running it on pump fuel .. from the info I've gathered looks like I'll be all right cranking it up 4+ I'll listen real good make sure there's no pinging or anything, Sent from my iPhone using Tapatalk Quote
bigweav81 Posted May 3, 2017 Report Posted May 3, 2017 Is it a stock/ machined head? Maybe I overlooked that part? Sent from my SM-S820L using Tapatalk Quote
bigweav81 Posted May 3, 2017 Report Posted May 3, 2017 Is it a stock/ machined head? Maybe I overlooked that part? Sent from my SM-S820L using Tapatalk Never mind lol Sent from my SM-S820L using Tapatalk 1 Quote
trickedcarbine Posted May 3, 2017 Report Posted May 3, 2017 Just give it a little timing at a time and make sure it's got fresh fuel. Quote
Columbus350 Posted May 6, 2017 Author Report Posted May 6, 2017 Just give it a little timing at a time and make sure it's got fresh fuel.will do Sent from my iPhone using Tapatalk Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.