Buster91dg Posted December 27, 2015 Report Share Posted December 27, 2015 Hey guys another problem with this headache. So now I go out today and started noticing a bog/back fire at high rpm esp when I really lay into it was fine for the first 20 min then I started noticed opens up stator side cover plastic part was slightly coated w water bike seemed fine last weekend have 30pilots 310 mains with fmf fattys pro design intake w k&n filter no lid. Bored 64.50. Needle 4th clip down from the top 1.5 air screws out please help before I sell this thing Quote Link to comment Share on other sites More sharing options...
Buster91dg Posted December 27, 2015 Author Report Share Posted December 27, 2015 Hey guys another problem with this headache. So now I go out today and started noticing a bog/back fire at high rpm esp when I really lay into it was fine for the first 20 min then I started noticed opens up stator side cover plastic part was slightly coated w water bike seemed fine last weekend have 30pilots 310 mains with fmf fattys pro design intake w k&n filter no lid. Bored 64.50. Needle 4th clip down from the top 1.5 air screws out please help before I sell this thingElevation is 282 as well if that helps Quote Link to comment Share on other sites More sharing options...
trickedcarbine Posted December 27, 2015 Report Share Posted December 27, 2015 Get the stator sealed up and dry and report back. Quote Link to comment Share on other sites More sharing options...
Buster91dg Posted December 27, 2015 Author Report Share Posted December 27, 2015 Any ideas for drying Quote Link to comment Share on other sites More sharing options...
trickedcarbine Posted December 27, 2015 Report Share Posted December 27, 2015 CRC electrical/contact cleaner. Then double check the pick up gap. From there make sure the factory rubber seal is in decent shape. If not get another or maybe try greasing yours. RTV works but is a pain in the dick to clean up off that sealing surface. Quote Link to comment Share on other sites More sharing options...
Buster91dg Posted December 27, 2015 Author Report Share Posted December 27, 2015 How do I measure the gap and I did spray that crc cleaner got a little better that's Abt it Quote Link to comment Share on other sites More sharing options...
Buster91dg Posted December 27, 2015 Author Report Share Posted December 27, 2015 It was fine last weekend that's what I don't understand Quote Link to comment Share on other sites More sharing options...
trickedcarbine Posted December 27, 2015 Report Share Posted December 27, 2015 Pick up gap is the gap between nubs on the fly wheel and the pick up coil. It should be about .020 or use a thin business card if you don't have feeler gauges. Quote Link to comment Share on other sites More sharing options...
trickedcarbine Posted December 27, 2015 Report Share Posted December 27, 2015 Spray out all the plug ends and use dielectric grease on the connections. Quote Link to comment Share on other sites More sharing options...
registered user Posted December 27, 2015 Report Share Posted December 27, 2015 .20 at the very most. with good crank bearings you can run it down even closer Quote Link to comment Share on other sites More sharing options...
Buster91dg Posted December 27, 2015 Author Report Share Posted December 27, 2015 Ok I have feeler gauges but don't know if there metric. Think there in inches Quote Link to comment Share on other sites More sharing options...
sleeper06 Posted December 27, 2015 Report Share Posted December 27, 2015 That's not a metric measurement .020". I always tighten mine down on a .018 feeler guage and after its all tight I get nice resistance on a .020 Quote Link to comment Share on other sites More sharing options...
Buster91dg Posted December 27, 2015 Author Report Share Posted December 27, 2015 So the pick up can be adjusted to magneto?? Quote Link to comment Share on other sites More sharing options...
sleeper06 Posted December 27, 2015 Report Share Posted December 27, 2015 Ya Quote Link to comment Share on other sites More sharing options...
Buster91dg Posted December 27, 2015 Author Report Share Posted December 27, 2015 Ok let me check it I'm working on it right biw Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.