snowmobra Posted May 7, 2015 Report Share Posted May 7, 2015 Just got this HOT ROD 4mil CRANK about 3weeks ago and the stator side bearing is shot. When split the case all of the other bearing were all oiled up. When I did the 4mil build my stock crank stator side bearing was shot to when I took it out. Can anyone help me. Thanks guys. Quote Link to comment Share on other sites More sharing options...
trickedcarbine Posted May 7, 2015 Report Share Posted May 7, 2015 So your motor toasted the outer stator side bearing on 2 different set ups? Hmm, first I'd look in to the cases and look for wear along the bearing surfaces. Check seals & gaskets and see if there's something on the mating surfaces as well. Quote Link to comment Share on other sites More sharing options...
snowmobra Posted May 7, 2015 Author Report Share Posted May 7, 2015 Ok thanks man. Quote Link to comment Share on other sites More sharing options...
snowmobra Posted May 7, 2015 Author Report Share Posted May 7, 2015 I'm just glad it's a bearing a not the crank and pistons. Quote Link to comment Share on other sites More sharing options...
registered user Posted May 7, 2015 Report Share Posted May 7, 2015 you may have issues with the case but the hotrods supplied bearings are nothing to write home about. when you compare them to a good bearing they look pretty cheesy Quote Link to comment Share on other sites More sharing options...
sleeper06 Posted May 7, 2015 Report Share Posted May 7, 2015 Should have have done a leakdown before tear down, now your just guessing Quote Link to comment Share on other sites More sharing options...
SHEEMAN0415 Posted May 7, 2015 Report Share Posted May 7, 2015 Did you do a leak down? Quote Link to comment Share on other sites More sharing options...
snowmobra Posted May 8, 2015 Author Report Share Posted May 8, 2015 YES had no leaks Quote Link to comment Share on other sites More sharing options...
Deadbeat Posted May 8, 2015 Report Share Posted May 8, 2015 how much compression and what octane gas you using, you said last time it leaned and failed out because your buddy left the gas tap off or half off or some shit Quote Link to comment Share on other sites More sharing options...
blowit Posted May 8, 2015 Report Share Posted May 8, 2015 I might be of some help here being a bearing guy. Might be easier to just email me. First thing to do is determine how the bearings failed? Exploded? melted? Those types of bearings fail usually for 3 different reasons assuming you stay within engineered margins. That is FOD (foreign object damage), too much axial force, roundness. If you are getting something in the bearing, the balls will be very dull looking with damage in the races. Axial force will show in the races as hot on the axial contact points. Roundness is a BIG deal and commonly overlooked. Both the inner shaft and outer race housing must have roundness and size to the spec of the bearing. Otherwise heat buildup will kill it. Imagine those balls having to constantly squash and deform to an irregular race clearance. This is similar to a tire....flattens out on the bottom where it makes contact. The right thing to do is clamp up the cases to torque spec and have a machine shop check the bore diameters for size and roundness. The half ass way is to clamp just that one bearing in the race and spin it to see if it feels right. I have seen perfect bearings destroyed in seconds because the race housing is out of round. They will make noise too. You may have oiling issues too that will cause heating. Examine the oiling holes and path. Brandon Mull Engineering Quote Link to comment Share on other sites More sharing options...
snowmobra Posted May 9, 2015 Author Report Share Posted May 9, 2015 Thanks man. I'm useing 93 40-1 Quote Link to comment Share on other sites More sharing options...
snowmobra Posted May 9, 2015 Author Report Share Posted May 9, 2015 Brandon my email shaunbullock18@gmail.com thanks bro Quote Link to comment Share on other sites More sharing options...
AKheathen Posted May 9, 2015 Report Share Posted May 9, 2015 check the oil passage from the cyclinder opening. Quote Link to comment Share on other sites More sharing options...
snowmobra Posted May 12, 2015 Author Report Share Posted May 12, 2015 What's the best bearings to get now Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.