notsed Posted August 12, 2012 Report Posted August 12, 2012 would it be a bad idea to run bb inframe shearers on my 421 as cast serval? how would they compare to sb pipes? its running on pump fuel Quote
WINDYCITYJOHN400 Posted August 12, 2012 Report Posted August 12, 2012 would it be a bad idea to run bb inframe shearers on my 421 as cast serval? how would they compare to sb pipes? its running on pump fuel Big bore Shearers would be Galacticly oversized for you motor and would be a very bad choice. If you read all the posts about this motor and your pipe choices...you'll find (after sifting through all the drama) that you have SB Shearers or PC pipes as the best choice so far. Quote
trickedcarbine Posted August 12, 2012 Report Posted August 12, 2012 would it be a bad idea to run bb inframe shearers on my 421 as cast serval? how would they compare to sb pipes? its running on pump fuel I would say an average 421 serval as cast on pump would definitely not benefit from the big bores. That motor would do just fine on the small bores. It takes quite a bit of heat/volume to make the big bores nessacary, Quote
possum Posted August 12, 2012 Report Posted August 12, 2012 Not to mention bb shearers dont fit on a smallbore application as the 421. Quote
ticktock Posted August 12, 2012 Report Posted August 12, 2012 Not to mention bb shearers dont fit on a smallbore application as the 421. Small flange big bore shelters fit on a stock cylinder... Pretty sure they fit a 421 serval. Just sayin Quote
possum Posted August 13, 2012 Report Posted August 13, 2012 The frame im talking about.. People putting the wrong pipes on and complain when they rub the frame!! Quote
vulvafan537240 Posted August 13, 2012 Report Posted August 13, 2012 Small flange big bore shelters fit on a stock cylinder... Pretty sure they fit a 421 serval. Just sayin you would likely have to raise the front of the motor to stop them from hitting the lower frame rails Quote
possum Posted August 13, 2012 Report Posted August 13, 2012 Or just use the proper pipe and run sbsf shearers! Quote
vulvafan537240 Posted August 13, 2012 Report Posted August 13, 2012 Or just use the proper pipe and run sbsf shearers! no need to get excited. im just trying to give the man some advice. either run sb's or jack the front end of the motor up. Quote
ticktock Posted August 13, 2012 Report Posted August 13, 2012 no need to get excited. im just trying to give the man some advice. either run sb's or jack the front end of the motor up. Custom mounts? JD's design? Might be a way to go. Quote
WINDYCITYJOHN400 Posted August 13, 2012 Report Posted August 13, 2012 Right......get some custom mounts, so you can put the wrong pipes on a motor. That way you can loose power but look tricked out while you do it. BB pipes are not even close to the right pipe for a Serval. Just because you can make something fit.....doesn't mean you should. Quote
ticktock Posted August 13, 2012 Report Posted August 13, 2012 Lol, sarcasm is hard to get off on the Internet! Quote
shanYE west Posted August 13, 2012 Report Posted August 13, 2012 Big bore Shearers would be Galacticly oversized for you motor and would be a very bad choice. If you read all the posts about this motor and your pipe choices...you'll find (after sifting through all the drama) that you have SB Shearers or PC pipes as the best choice so far. the CPI's looked just as good as the other 2 imo. CPI FTW!! Quote
guns4children Posted August 13, 2012 Report Posted August 13, 2012 Right......get some custom mounts, so you can put the wrong pipes on a motor. That way you can loose power but look tricked out while you do it. BB pipes are not even close to the right pipe for a Serval. Just because you can make something fit.....doesn't mean you should. yeah what about CPI? i also thought you were hating on running PC pipes on a serval? Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.