Search the Community
Showing results for tags 'ported cylinders'.
I've got a set of stock cylinders with a stock stroke dune/play port by Jeff at F.A.S.T. The only reason I'm selling is because I'm upgrading to cubs. Before I tore the bike down, each cylinder had 135-140 psi with 20cc domes at 1000ft asl. I'm assuming they'll need a fresh bore and hone before reinstalling them, but I'll send the pistons with the cylinders if someone wants to use them again. The bike ran fine prior to taking everything apart. I don't have any gauges to measure the bore, but the wisecos are 513M06500, which I think means the bore is .050 over stock? Please correct me if I'm wrong. Both bores feel smooth to the touch. I couldn't notice any ridges or scratches along the bore with my fingernail. $225 The crank is hot rods stock stroke. As you can see from the pics, I got a little carried away with sealant the last time I put the cases together. Despite my overzealous use of sealant, the bike ran great and the bearings spin freely with no binding or grinding. I don't have an v-blocks or measuring tools to test the bearings roundness or run-out, but as I said earlier, they still spin nice and smooth and came from a good running motor. I was able to get a hold of some feeler gauges to measure the connecting rod side clearance. According to the manual, connecting rod side clearance should be between 0.25-0.75mm. As you can see, I got 0.50mm on both rods. I'll be more than happy to provide additional pics if someone has concerns. The only thing I've noticed that MIGHT need replacing would be the bearing on the flywheel side of the motor. It spins freely with no grinding or noise, but it's the only bearing that I could notice with some axial play. It might be just fine, but I have no idea and haven't dealt with enough crankshafts to know one way or the other. $150 Lastly, I also have a lovely set of stock carbs with the god awful TORS still attached. I also have the K&N clamp-on pod filters that go with the stock carbs. I don't have pics of the filters yet, will post tomorrow. The filters aren't pretty, but functional. I've also got black outerwears that I'll include, they're also pretty rough. I believe the carbs have a 27.5 pilot and 300 mains. The carbs do include the attached throttle cable. If anyone has any questions, just let me know. $70 for the carbs, $20 for the filters and outerwears. <iframe width="480" height="360" src="http://s629.photobucket.com/user/bavhx4/embed/slideshow/Banshee"></iframe>
I have a lot of parts to swap. I have a stock transmission (not in the picture) in good condition off a running bike. I also have everything pictured here. The stator wires are cut, but did come off a running bike (it was just wired like shit) there are 2 stock baskets, one looks brand new and the other has some grooving and a couple knicks in on some gear teeth, it rolled smooth though and was off a running bike. there are lots of parts as well as these cases that were from a running sealed bike. Has a pretty good chain whack on it. I will clean them up more before shipping. I have these CT dune ported cylinders as well as namura pistons and the stock crank. The only thing not pictured is some spots on the cylinders are repaired with heli coils, these all came off a running bike. I also have a set of boyesen reeds from the same running bike. I have a lot of smaller parts, two of each, and wont be needing both, so feel free to ask. I am not saying anything here is in awesome condition and if its not for you I don't really care to hear about it, its just stuff I wont need and it might help someone get back up and moving again before a trip or something someone could use for a cheap build project. I am looking for a GOOD set of +2+1 J arms and tie rods for my project. They would need to be for the 90s J arm banshees. Or I would be interested in an A arm conversion kit with +2+1 A arms. Not looking for anything with chrome. Also looking for: Billet clutch housing NEW flywheel Stock length round house swing arm Billet water pump gear Good carbs without TORS I am building a mild 4 mil so if you have anything that think might be of use... Just TEXT me at 17128996473