bertski077

i got a question for u guys...my carrier is a little shot on the sprocket side b/c of the spun bearings, is it bad if i have about 1/16th gap btwn the sprocket and the carrier, where the seals go outside of the bearings??

yeah i have the bike supported by a stand and the rear wheels are off...if i sawzall it how much would that help b/c i culd only saw zall the tip of the bolt...and if i heat it up where would i heat it up b/c the heat would have to penetrate the swingarm and the housing the bolt slides through?? thanks for the tip im gonna be at it again tomm. so let me know asap.

im trying to replace my swingarm bearings...i took the nut off the pivot bolt...but the pivot bolt wont slide out, i tried beating it and beating it but it wont come out...i got it to come out about 1/16 of an inch thats bout it...any thing would help, thanks alot.

i am looking for a set of +2 a arms reasonably priced reply or PM me with what ya got. thanks

i just cleaned the carbs a lil while ago...im running 32 to 1 with hr1 oil(expensive shit) i need to do the compression check for sure. i thought tht i had sync'd my carbs pirfect maybe i need to check them again...but if they were out of sync wouldnt it smoke all the time not just wen its cold?

wats up guys...i got a 99 banshee with pretty low hours on it its on the stock pistons/rings...when i first start it up , it smokes a little from the left and more from the right then it will only smoke from the right one...but when im riding it, the smoke stops and its fine...i dont know if the right carb is running rich? or i might need rings or a new top end...i dont have any power loss at all..what could this be???

want ext. a-arms or ext. axle ne one???

yeah thts wat i think cept im puttin a ext. axle on it...i was wondering how this things gonna handle since i got a stock front end w/ a ext axle...i have 450 shocks in my garage ready to go on im juust waitn till i get the ext. a arms...but i was just wondering how wierd its gonna be with ext swing arm and stock front end...?

yeah it looks like on the outer edge of the carrier there is something melted it doesnt look like the carrier got melted although it may have turned blue from heating up a SLIGHT bit

due to my axle failure, i am buying a g-force +4 axle for my shee...i was wondering how my handling will be if i have stock a-arms and a +4 axle??? +2 a arms were going to go one but now that my axle bearings went i might as well just put a new axle on while i have it apart

i was riding the shee today n wen i was on the pavement i herd a squeek from the bike, i hit both brakes and it wasnt the brakes squeeking...so i kept goin...all of a sudden it felt like i had a flat spot in my tire the bike was vibrating...i got home and it had lookd like the bearing or seal was melted on the sproket side of my axle...it was not locked up completly but close...could this have put my axle carrier out of round???

could the wires be burnt near the back right exhaust...? if you have an ohmeter and a manual check to see wat kinda current your suppose to get out of the stator...you can also check to see if your pickup coil is bad

i was wondering if anyone knew if you can put yzf450 shocks on banshee plus 2 a-arms and just bolt it on?? thanks for the help...and how good are the new 450 shocks?

a very important thing to remember is if your gonna hit a jump u HAVE to commit to the jump you CANNOT back out at the last second good luck im still tryin to learn im racing mx on my shee next season

what lbs and wat a-arms are the shocks for? and do they need to be rebuilt??? very interested thanks ben

will warrior front shocks fit on a banshee if both are

im sorry i meant i need shocks for stand. length a.arms...if u have ext. arms i would be interested

front suspension std arms w/ resivors...nerf bars and extended axle

i was wondering if i bought shocks that were on a warrior if anyone knows if they would fit on a banshee...on the add is says they would but i want to make sure b4 i purchase them...they are for stock warrior a-arms and i have stock banshee a-arms. thanks for the input

can u email me some pics and the price of the nerf bars at [email protected]/

i got a 99 shee im in Philly,PA tho. it has toomey t5s, jet kit, renthal bars, t.o.r.s removal kit and dominator rear tires. if your interested email me at [email protected].

i dont know about ne one else but i find it a real bitch to put the front plastic all on especially the rad. cover...is there anyway to solve this via. a aftermarket hood or just drilling own holes??? thanks

i wanted to hear from any one who has a mx shee...how they make out against the other riders on different quads...and what they have done to it.

my clutch is really hard to pull in and it lets out really far...it still disengages all the way but is this a sign that i need a new clutch?...also, i have gotten the t.o.r.s removal kit...what do i do with the wires coming from the throttle and the plugs that are under the gas tank...SOMEBODY PLEESSSE HELP!

well...if i get good enough i'll do organized but im from PA n there arent many atv tracks around plust its expensive...i'd like to keep it around 1g for the setup...i duno if thats possible tho...maybe i'll find some stuff on ebay?