WALLACE84

Anybody who wants pics post up your email.Thanks -Dan

Motosport Outlet has some mod quad 4mm domes that will fit a pd coolhead for a decent price. Check them out

I dont know for sure but I think it is shee male. Hes makes graphics so send me a PM.

I have a set of t5's. I will email you some pics. Thanks

what kind of timing plate is it?

I have the front brake master cylinder and lever,I cant post pics up on here for some reason tried about a billion times but I cant so send me your email and I will send you some pics of it.

I will send pics out tommrrow and make me an offer on the skid plate. I have a full set of 02 blue plastics dante that have race cut fronts that arent in bad condition but the rears have some stress marks. A heat gun will take alot of them out. I will send pics of them to you tommrrow oh and I have a set of stock headlights if you just want them. Thanks

I had the wiring harness on an 02 motor and make me an offer on the swingarms. One is in good condintion and the other has a jacked mount hole for the carrier but other then that its fine. I will send pics today if I get a chance if not then tommrrow for sure.Thanks

I have a powdercoated blue a arm frame for sale. Oh and I also WAS going to buy parts from this dude :verymad:

Oh nevermind then. thanks anyways

Would he trade the setup for anything? if not then I will buy it in about a week when I get some extra cash

Where are you located?

They both in good condition but one has some fins bent but the other is almost like new. Whats your email address?

I will be on!! :thumbsup:

Im starting to clean out my loft and get rid of the parts im not using for my build up. Here they are : -2 stock swingarm -1 dogbone -under belly skid plate -2 stock radiators -stock stem -cylinders (I was told they are .60 over) -motor mounts -wiring harness -left bottom a arm -leftside spindle/rotor and tie rod Make offers I might be forgetting some things. I will post more up if I find any.Thanks -Dan

What do you want for those blue plastics? Thanks -Dan

Im getting play/dune port on some .20 over cylinders and then on my backup cylinders im getting them drag ported

Lol sounds like a deal. Reason I siad NYUK wasa because he said that to someone before

Damn!,I wish I had the money sounds like a good deal. Tell him I will trade him my chicken nuggents and orange drink for it!! NYUK

I know I have made a couple post on this subject before but now that my shee is almost done again, I wanted to know what you guys with +4's think about them. I debating on getting either a stock length roundhouse or a -1, -2 roundhouse because I go to the dunes and liek to drag my friends but also ride trails once in a while and do some jumping and wanted to know what you guys input on trail riding and jumping was on them. I have never ran a extended swinger they have always been either stock roundhouse or -1s. Thanks for looking -Dan

I have a blue powdercoated a arm frame that I have just sitting at my shop after I did a frame swap that I dont need anymore. I havent checked the vin number but I was told its a 2002 frame. I can get pics upon request. Make me some offers or if you want to trade soemthing let me know. Located in Midland, Michigan. Thanks -Dan

Ive chewed since I was about 12 and now im 17. I have tried to quit uncountable times and just cant do it. I will make it 3 days tops

Pm me for pics. I can't get them small enough to post without them being blurry

Well its back up for sale again. This time though, I NEED the money for my truck. The bike is all balck with n style graphics,pro taper 1 1/8 bars,new renthal black sprockets and chain,unadilla rear tire,uni air filter,fmf pipe and silencer,boyesen reeds,new fork seal on left side,new odds and ends parts like clutch perch and lever,killswitch,909 grips,gaskets for powervalve,and axle nut. First $1100 takes it. If soemone buys it soon I throew in a free jeresy too lol. Thanks -Dan

I like it. $1800 aint a bad deal, I say go for it!!