RagunCajun Posted July 19, 2007 Report Posted July 19, 2007 (edited) I'm installing my gforce axel after having for over a month. I lost the instructions but i wanna get this done before the weekend. I have the side with the brake rotor all done. I need to know how to do the other side. Is it the big nut, metal round thing then the clip or what? Also do i need to use a big wrench to put the nut tight or not? Once again, i need to know how to arrange the parts from the rear sprocket on out(to the left when in back of the bike looking at it). I think i explained well enough but if not, please let me know. thanx, cody edit* here are some pics. In the first, x marks the starting point and the arrow marks from there when to put on. I might have done it right but i want to make sure. Last thing i want is it to mess up spinning at a very high RPM. http://www.2sly4.us/rc/codys_stuff/MyBansh...07%20edited.jpg http://www.2sly4.us/rc/codys_stuff/MyBansh...3%207-18-07.JPG this picture is the otherside. It's all done. I think it's the right way. http://www.2sly4.us/rc/codys_stuff/MyBansh...2%207-18-07.JPG Edited July 19, 2007 by RagunCajun Quote
375hp banshees Posted July 19, 2007 Report Posted July 19, 2007 I'm installing my gforce axel after having for over a month. I lost the instructions but i wanna get this done before the weekend. I have the side with the brake rotor all done. I need to know how to do the other side. Is it the big nut, metal round thing then the clip or what? Also do i need to use a big wrench to put the nut tight or not? Once again, i need to know how to arrange the parts from the rear sprocket on out(to the left when in back of the bike looking at it). I think i explained well enough but if not, please let me know. thanx, cody edit* here are some pics. In the first, x marks the starting point and the arrow marks from there when to put on. I might have done it right but i want to make sure. Last thing i want is it to mess up spinning at a very high RPM. http://www.2sly4.us/rc/codys_stuff/MyBansh...07%20edited.jpg http://www.2sly4.us/rc/codys_stuff/MyBansh...3%207-18-07.JPG this picture is the otherside. It's all done. I think it's the right way. http://www.2sly4.us/rc/codys_stuff/MyBansh...2%207-18-07.JPG THATS BACKWARDS!!! i'll send ya some pics as i just id mine & Kiel sent me some pic's here ya go right side looks ok another thanks again Kiel & ghostrider (though you probably weren't aware :biggrin: ) Quote
RagunCajun Posted July 19, 2007 Author Report Posted July 19, 2007 Damn did i get it backwards haha. So from inside going out, it's the spacer, clip then the big nut? thanx man. So i did the brake rotor side wrong too? from outside going in, it was the clip then the round thing with the reccessed part. Quote
SandShots Posted July 19, 2007 Report Posted July 19, 2007 what swingarm and carrier are you using? Quote
375hp banshees Posted July 19, 2007 Report Posted July 19, 2007 Damn did i get it backwards haha. So from inside going out, it's the spacer, clip then the big nut? thanx man. So i did the brake rotor side wrong too? from outside going in, it was the clip then the round thing with the reccessed part. i think you ( and i) got the RIGHT side correct but... ok the instructions suck but rt side-take the smaller spacer slide it between the axle bearing & larger dia. splines(it will cover up a small part of the splines)*w/ the flat side towards the rotor& the groved towards the wheel hub so the snap ring will go into it) *thats how i read that & i 'm sure its correct but you can see how bad the instructions are so do what you think! install rotor hub slide axle into housing install the sproket hub left side 1) install the 3 piece lock nut OUTER piece goes 1 st ( my 3 - piece nut was all together & i put it on w/ the hex out like the pic) 2) install theC-clip the inner piece of the 3-piece lock nut will rest over the C-clip 3) using medium locktite ALLEN HEAD bolt & torque to 8 'ftlbs 4 for the narrowest (which is wider than stock)install the small spacer on the axil EDIT: i typo'd the first post so reread it here is what is wrong & it makes A big difference!!!! 3) using medium locktite ALLEN HEAD bolt & torque to 8 'ftlbs think you ( and i) got the RIGHT side correct but... Quote
RagunCajun Posted July 19, 2007 Author Report Posted July 19, 2007 4 for the narrowest (which is wider than stock)install the small spacer on the axil That's the things on the end that the wheel hubs go against right? Quote
375hp banshees Posted July 19, 2007 Report Posted July 19, 2007 4 for the narrowest (which is wider than stock)install the small spacer on the axil That's the things on the end that the wheel hubs go against right? yes, & i guess you have to atleast, have the small one on ? Quote
RagunCajun Posted July 19, 2007 Author Report Posted July 19, 2007 yes, & i guess you have to atleast, have the small one on ? No i actualy stopped short of completing the install. I was in fear that i didnt do it right and it would take longer to take it all down and correct.....luckly i asked first heh. Yeah i have two, a small and a larger one. Im going wide as possible in the rear cuz i have the yfz450 front end. thanx man! Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.