350cc stock cylinder drag motor

[BB3]

First off we have Foxgirls (christys) 350 stock cylinder motor going up for sale, the cylinders are .40 over and maybe 6-7 races on them.

The cylinders where ported by Bubba297 which if anyone know how he is he know's his stuff for sure also the cases are port matched to the cylinders, the crank is stock but has been rebuilt before going in the motor and was true and welded up.

Now the inside gooddies, cool head with 18cc alky cut domes,upp 35mm intakes, VF2 reeds,billet stator cover,adjustable timing plate,lightend flywheel,stator, direct drive lockout and stock modded cover with removeable cover,1-5 netrual down override (shifts smooth as butter) billet water pump impeller, barrent clutch pack with stock springs.

 

This motor in a stock chassis that weighted 295#s wet ran a 4.21 @ Andy's track in Oklahoma and ran some 4.2's and 4.3's @ the neb. track and also ran some 4.3's @ big river sand drags in Mo.

 

This motor is no punk for sure and i think in a rigid chassis this motor SHOULD pull some high 4.0's and low 4.1's.

 

Asking $1500 for the motor plus shipping.

 

 

 

 

 

Next

We have some 36/38mm lectrons with a single power jet, these right now are setup for alky but have the needles to change them back over to Gas if somene wanted to swap them back comes with Throttle cable.

 

Side pic's of them are with the motor pic's.

 

$300 plus shipping

 

 

 

 

Next

 

I have a +8 GT performance 1 off custom swingarm that has been chromed but would need to be re-chromed to be perfect again, you can see the brown spot where the chain guide was welded on and never re-coated Also has mounts on the bottom of the swingarm for a wheelie bar.

 

$275 for the swingarm plus shipping.

 

I also have a Hillshooter JJ&A drag axle it is a yfz drag but is setup for a banshee, i have the brake hub and spacers to convert it back to a yfz if someone wanted to do it.

Also comes with the brake rotor and the 40, 42 rear sprocket i think i even have a 39 tooth as well i will throw in as well.

Has a few marks where the chain came off but not to bad, this swingarm also come's with the Billet carrier that it is in now.

Dont want to separate it.

 

Asking $425 for axle, sprockets and carrier.

 

If someone is interesed i will do a package deal on the swingarm, axle and carrier for $650 plus shipping

 

 

Only things for sale are what is posted thanks for looking

 

BobbyIII

[BB3]

$300 shipped for the carbs

$275 shipped for the swingarm

$400 shipped for the axle and carrier.

[87sheerips]

Bump for a good guy, Ive heard lots of good things about this motor guys!!

[BB3]

Thanks JDS.

 

Offers?

[bansheejoel]

so let me get this rite, stock stroke and stock cylinders turning 4.2's? Holy shit! Im really impressed

[BB3]

so let me get this rite, stock stroke and stock cylinders turning 4.2's? Holy shit! Im really impressed

Yes sir and in a stock chassis as well.

[tedd1]

This setup has put a whoopin' on a lot of bigger motors.

(Don't ask me how I know! )

[BB3]

Dont worry your secret is safe with me.....Lol.....thanks Rick.

[dajogejr]

BBIII forgot to tell you all his wife weighs 38.90 pounds and he imported her from Ethiopia...

 

J/K.

 

Good luck to ya B!! Somebody needs a drag race beginner motor that will run with some much bigger dogs!!!

[VegasJeff]

BBIII forgot to tell you all his wife weighs 38.90 pounds and he imported her from Ethiopia...

 

J/K.

 

Good luck to ya B!! Somebody needs a drag race beginner motor that will run with some much bigger dogs!!!

good one dajo

[BB3]

well i run about the same times and i weight 170#s

[BB3]

carbs sold.

[BB3]

Axle and carrier Sold.

 

$250 for the swingarm

Motor still for sale $1500

[BB3]

Will sell the cylinders,pistons,cool head and both set's of Domes intake boots and reeds for $600 shipped.

[BB3]

Up