dune bike

[4strokekilla5]

Im building my 87 shee into a dune/some what of a race bike. so far im sending in my jugs for a dune port from hjr, i have a rev box, +4 timing, carbon fiber reeds, next i need to know what else i should do, i need pipes and carbs forsure i would like some suggestions on those and anything else im missing.

[lowbuckracing]

Stock stroke?You can run stock carbs with bigger Jets for now..depending on how your planning for the future in your build,a set of Shearer inframes are a good pipe.t-5 or cpi would also be a nice choice...Ask Kevin what his port is gonna need to get the most out of it..good luck and a great choice on the machinist

[4strokekilla5]

Stock stroke?You can run stock carbs with bigger Jets for now..depending on how your planning for the future in your build,a set of Shearer inframes are a good pipe.t-5 or cpi would also be a nice choice...Ask Kevin what his port is gonna need to get the most out of it..good luck and a great choice on the machinist

yes stock stroke and i was thinking about shearer or cpi's but its kinda hard to find a good set of chrome cpis for 400$ used. and i was thinking 33pwk carbs maybe?

[uwenr]

yes stock stroke and i was thinking about shearer or cpi's but its kinda hard to find a good set of chrome cpis for 400$ used. and i was thinking 33pwk carbs maybe?

A set of CPI's and some 33s that bike should rip. Dont forget after doing all of that you will need more paddle and spocket. Like a 9 or 10 paddle hauler and like 15-41 gearing.

[lowbuckracing]

I seen a few pair of pipes on PS...for around your $ range..Also 33s would work fine..

[4strokekilla5]

I seen a few pair of pipes on PS...for around your $ range..Also 33s would work fine..

alright sounds good to me guys thanks, kevin says i should be runnin around 85hp on pump gas if i set it up right. i cant wait :]!!!

[lowbuckracing]

pm torque-racing here on the hq..I think he selling some CPIs for around 400...Pretty new..

[4strokekilla5]

pm torque-racing here on the hq..I think he selling some CPIs for around 400...Pretty new..

mk i will thank you.

 

i might as well adress my next problem im leaking oil out of the shifter shaft, i obviously need to replace the seal there how do i go about removing the shaft. i already have the clutch case off.

[trex565]

try ebay thought i saw some on there and for tte seal think it will come out with out taking apart but you better ask

[uwenr]

mk i will thank you.

 

i might as well adress my next problem im leaking oil out of the shifter shaft, i obviously need to replace the seal there how do i go about removing the shaft. i already have the clutch case off.

 

You can replace it without pulling it apart. lean the bike over and pull the old one out with a pick. Pack the new one with grease and slide it in. You can also do the one behind the sprocket the same way.

[4strokekilla5]

You can replace it without pulling it apart. lean the bike over and pull the old one out with a pick. Pack the new one with grease and slide it in. You can also do the one behind the sprocket the same way.

basicly your saying i can use some vise grips a tug it outa there?

[4strokekilla5]

also should i buy a +2 or +4 swingarm for dunes

[Tf705]

kevin told you 85 hp. i was talking to him last week about my combo and he told me i would have around 70 to 75hp. i have his drag port with cpi inframes and 35 mm carbs +6 timing, vforce reeds, cool head with 18cc domes. but you definetley need to go plus 4 or 6 on the swingarm.

[4strokekilla5]

kevin told you 85 hp. i was talking to him last week about my combo and he told me i would have around 70 to 75hp. i have his drag port with cpi inframes and 35 mm carbs +6 timing, vforce reeds, cool head with 18cc domes. but you definetley need to go plus 4 or 6 on the swingarm.

yeah my bad idk what i was thinking he told me 65-70hp