LT ROOKIE

Hi, I am selling a set of very clean 41 pwk alky carbs. They are gravity fed, have 120 dump tubes, and oversized billet bowls. Asking 525.00

I forgot to ask, are u running a wheelie bar? How long?

Looking for a +8 or 10 ladder bar swingarm. would like to find a sleller machine performance one with the torque bar. Thanks

about 1800, it has J&A drag axle, drag a arms, aftermarket steering stem, drag cut seat, and plus 8 swingarm.

if the motor sells I will sell the rolling frame as well

I am in hollywood,fl and will try to post pics tomorrow. I can be reached at 954 662-9030 mark

Hi, I am selling a new 14mm cheetah dm motor. Motor includes new complete dm topend with v3 reeds and billet intakes, hinson clutch basket with springs, straight cut gears, 14mm billet twister crank, and new billet casses. Topend and cases were done by dan hall. It also comes with new shearer bboof pipes with silencers and 41 pwk carbs with dave moore powerjets and billet bowls. The motor does not come with a transmission, it's for sale on ebay. I have too much money into this project and it's still not done. I need a drag frame, billet transmission,wheelie bar and swingarm. This would cost me another 5-6 thousand dollars on top of the thousands I already have invested, so this is why I am selling this stuff. I also have a rolling 2001 frame setup for asphalt. I am asking 5900.00 for the motor setup. I

were your times faster with the 8 or 14

Thanks for the info. I am going to go with a 10 over ladderbar swingarm from steller. will let you know how it works.

Thanks for the reply. I am 220 pounds and have a plus 8 aerotube already. I know steller sells a ladderbar with the torque bar to prevent the arm from pulling. So i shouldn't go shorter than 10. anyone out there running a shorter arm on a similar set up.

Hi everyone, I need help with my setup. I am building a 14mm dm for the 1/8 mile asphalt. It has a stock frame with drag lite a arms and struts all around. I will be running american racers 20.5 sd23 rear tires and a wheelie bar. What is the shortest swingarm I can run without the ride being so violent out the hole. Also my builder wants me to run a ladder bar swingarm because it has less flex and will provide more traction. Is this true.

Sent you a second email with the correct number. I gave you my old number.

trying to sell complete motor, if not I am going to assemble and run it

Got motor from dan last week, still for sell. Pm sent

Has labelle been shut down? Was thinking about going this sunday

I have 41 pwks with dave moore power jets and oversized billet bowls. last week I asked Dan to order the pipes so I will find out tomorrow if I will have pipes for the motor. If yes, they will be shearer rubber mounted chrome pipes, two out the left side with egt tabs

I am building a 14mm cheetah dm motor for 1/8 mile drags. I was going to race this motor but just had a little girl and my wife in scared of me getting hurt. motor should be complete this week and I am looking to sell complete or in parts. Complete brand new 14mm dm topend with intakes drag ported by dan hall 2000.00, new billet cases with used in good condition 14mm billet twister crank with 125 rods 2400.00, 1-5 tranny with billet second gear 400.00, billet hinson clutch basket with springs new toomy clutches and direct drive lockout with cover and red see through lens 550.00. transmission and clutch will be sold once top and bottom end are sold. any questions call mark at 954 347 2432.

I have a 14mm asphalt drag banshee I am considering selling. The quad has 14mm cheetah cylinders, v3 reeds, hinson billet clutch basket with springs, shearer big bore big flange oof pipes, and 40mm alky lectron carbs with billet bowls and fuel pump. The cases were expoxied and trenched by k&t. The cylinders were ported by a local builder for shearer pipes. The quad needs to be tuned for 1/8 mile and needs new slicks in the rear. The quad is candy red with candy red and yellow flame plastics. The motor is currently apart having the tranny replaced. I have a wcr 1-6 override tranny that took a sh-t. I am ordering a new tranny with a billet second gear set. I am asking 6500.00 I will post pics if I get serious replies from people that are interested in buying. If you have questions you can call mark at 954 347-2432.

I will post pics on friday. I am running a fuel pump and a pe1 rod. I have tried to tune these carbs for my 14mill cheetah but have been unsucessfull. I am going to switch to 41pwks. If the cables fit the pwks i will keep them if they dont i will give them with the lectrons.

I have a set of 40mm lectron carbs setup for alky. Carbs have dual powerjets and packard billet bowls. I am asking 325.00 mark 954 347-2432