yamaha_daniel

ok so i finally got my shee together its bored 100 over fresh two day ago top end rebuild..i bought it in pieces and put it back together cleaned the carbs and bored the jugs ....now i suck so bad when it comes to carbs so i absolutly need some help on this one.;..i can start it easy 1st or 2nd kick it starts it wont idle but from what i heard its hard to get a banshee to idle so thats no big deal annyway when i put it in gear and take off it spitters and sputters and runs like crap hold it wide open untill it hits the power band and then it runs okay as long as you keep it in the band as soon as you let it out it does the same thing my mods are ... airbox lid removed, reed spacers, tors removed, e-brake removed, boost bottle, bored .100 over, Dg all the way back ,,,,,,,,,,,,,,,,,,,any and all help is appreciated also im mixing my gas 4 to 1 or 32:1 thanks- dan

mine also has these holes i figure they are to drain out water if it gets on the engine .... they are also sloped a little bit ...-dan

here you go i found these but i personally dont think id pay that price for some food coloring and clear hose ... here you go -dan http://www.rockymountainatvmc.com/productD...5#vehicleSelect http://www.rockymountainatvmc.com/productD...odFamilyId=2806

thanks everyone ill take what seems to be common in all of those and use it -dan

well i thought if everyone listed the way they did it i could take some advice from everyone thanks all -dan

what is the proper break in technique ive heard that you need to baby it untill like 4 hours or something like that list what works best for you !!! -dan

hey!!! your money order went into the little blue box on the street corner today ..thanks-dan

ill send you the money order tomorrow....thanks-dan

hey i use this kinda helps a little bit .... http://wiseco.com/PDFs/Catalogs/2008/CB/YamahaATV.pdf

hey its kool about the tie rods .....could you pm me your mailing address so i can send you the money order thanks-dan

hey id like to purchase the a arms for the price you told me ... could you give me your mailing address so i can send you the money order ,,,,,forget about that pm earlier about the pics ,,,,,,how much extra for a passenger side inner tie rod end? thanks -dan

thanks everyone im pending a deal with a hq forum member-dan

hey i need upper and lower a arms and a left inner tierod end thanks -dan

hey buddy ,,,,,, no damp spots anywhere there should be somewhere are you bleeding both fronts? ...check around the piston on each brake caliper....im having a bleeding issue myself my bleeder screw is broke off and i cant figure out how to get it out. hope this might help

im not sure about the jugs but i got my piston kit from here,,,,,,,, http://www.motosport.com/offroad/product/W...91&cat0=ATV they give you ....Piston kits include: Balanced set of Wiseco forged high-performance pistons, rings, wrist pins, circlips, needle bearings & top end gasket kit...hey!! and you meet the 2 day free shipping maybe ebay or something for the jugs

i have talked to both jeff and kevin... im just going to get it bored/honed right now b/c i plan on getting new pipes soon and im a cheap a$$ and i only want to pay for the porting once , lol thanks -dan

hey thanks for the replys with the links to the archives ill read them -dan

im sorry but i tryed to search it maybe i typed in the wrong thing this is what i got The error returned was: One or all of your search keywords were below 3 characters or you searched for words which are not allowed, such as 'html', 'img', etc, please go back and increase the length of these search keywords or choose different keywords and i tryed to type in different searches on a arms still the same thing ive read and read and read posts in the archives many times and ive also seen in many posts that " you should have used the search button, this has been gone over 242443121616 times" i wouldnt have posted this but i couldnt find anything on it. it seems that some people do use the search....i am also not being a ass but replys like that one makes me just want to hang around and read posts not post any. but that might just be me. -dan also thanks for the reply it IS appreciated

just wondering if this would be a good deal any comments appreciated-dan http://item.express.ebay.com/ASR-Banshee-2...cmdZExpressItem

i called the local shop and they wouldnt give me a price for porting ...i asked for the price on a bore job and the guy said after taxes about 92.00..i was like wooooooo i then said per jug? ?? and he said yeah i then said thanks have a nice day.-daniel

i need to bore my jugs over but the local shop is out of there mind can anyone on here do it and who would you reccomend please list prices thanks-daniel p.s. im thinking about getting them ported also .

hey nice job i so would like to learn how to polish ,,,,what meathod did you use ...what polishing compound and technique did you use thanks - dan .. ps sorry for the spelling.

bump ttt

i live in Glean Jean in Fayette Co. west virginia

just like the title says what method do you use to polish your exhaust system (header/silencer)-dan post some pic's to show us what they look like