98golded

Sold!!

Bump for a good lookin helmet, too bad it's not red & black!

Read the first post, can't haul, have no way. The rear shock is a stock shock revalved for a 220lb rider by TCS. Carbs are stock, just jetted. No title, titles aren't required in KY.

Still for sale... bump

Yep, as of this moment it is. No one has shown me any cash yet.

Alright, here's an update. For anyone who thinks they're gonna lowball me, until I get enough interest in the other parts on the quad, the wheels aren't going anywhere. 700 plus the ride for the wheels and tires, will not seperate, must all go together. Like new, only seen wet grass, not even on the pipe. 350 plus the ride for the front shocks, set up for a 200 lb rider 150 plus the ride for the rear shock, rebuilt and revalved by TCS for a 220 lb rider 375 plus the ride for the pipes These are just estimates, if I get enough hits on this stuff I'll consider parting it out, if not, it goes whole or it sits.

The failure rate for PS3's are 1.2 percent as to the xbox failure rate being 26 percent, last I checked, this may or may not be accurate. I have both an xbox 360 and a PS3. Good to see you got a deal though, now go buy a 320 gig hard drive with some of that extra 200 bucks.

I'm located in Northern Kentucky, about 20 minutes from Portsmouth Ohio on the Kentucky side if you know whereabouts that is. I'd consider parting it out of I got enough interest in all the parts. Until I get enough interest in parts I'm gonna try and sell it whole. It's well worth 2k.

Up for sale is the project I've been working on. Built this thing to keep but job issues force me to sell it (unemployment blows). Been workin on this thing for 2 years, here's a list of what's been done. -New Transparent Red powdercoat on the frame, wheel hubs, sprocket and brake hub -New stock bore topend, unported w/ Pro-Lites -New bottom end bearings in the crank and tranny, as well as new seals for the cases -New bearings and bushings including swingarm, a-arms, wheel bearings, axle bearings and steering stem bushing -New Elka Dual rate front shocks w/o reservoirs, threaded preload adjustable w/ Elka shock covers -New Hiper Beadlocks front and rear w/ black rings, 4+1 Offset up front, 4+5 on the rears -New ITP Trac Star Rear tires 20x10-9 and 21x7-10 Razrs up front, 3 rides on them -New silver powder on the swingarm and axle carrier -New ASV F-3 levers -New Clutch & Throttle Cables -V-Force 3 Reeds -Toomey TR-6 Chrome Pipes -Alba Aluminum proflow plate with K&N Filter and Precharger -New MSR Gunmetal Finish Handlebars I originally began this build with the intentions of having a high performance, stable trail quad. Never really intended to sell the thing, but 2 kids later and standing in the unemployment line gives different views. The quad DOES run and you can ride it, but it needs plastic and for some reason I couldn't get the front brakes to bleed out, I think the calipers may be frozen because I can watch the lines flex. All the parts that were put on were installed by me with all new fasteners and hardware. I stripped this thing down to nothing, as most of anyone knows you have to do with a ground up build. Asking 2k, no trades, need the cash. Here are pics, and can take more pics upon request.

The only negative things I've heard about the full flight arms is that the heims they use are weak. The construction of the arms themselves are alright from what I hear, just the weak heims they use.

Cylinders are sold. Adding a set of stock a-arms, all ball joints good, bushings good, come with sleeves and endcaps. 90 shipped. can post pics on request.

Still got the book?

Anybody? Make offers, I need to get rid of this stuff. Don't need much more before I can get it on it's wheels.

First time putting anything up for sale on here. Just looking to get rid of the few parts that I don't need, to keep funding my shee build. Stock port cylinders, currently 65mm bore, need bored again, piece of the ring broke and nicked the right side cylinder. might be able to get away with going .050 over, I'd probably go 60 just to be safe. I'd like to get $160 shipped outta these to buy a new set of pistons for the other jugs I've got. Stock front brake setup, no pads included, or hard lines. Just the rubber lines, splitter, calipers and master cylinder. I'd like to get $50 shipped out of these. Two stock heads, both unmilled, one has a few chamber scuffs, looks like detonation to me. Make offer on the heads, I've got no clue what they're worth. Can email pics upon request. dtaulbee@windstream.net questions about the cylinders, you can call my cell 606 922 6770, my zip is 41179. This might help, a link to my ebay feedback. http://feedback.ebay.com/ws/eBayISAPI.dll?...tab=AllFeedback